tactility/Devices/es3c28p/Source/Configuration.cpp

#include "PwmBacklight.h"
#include "devices/Display.h"
#include <driver/gpio.h>

#include <tactility/device.h>
#include <tactility/drivers/i2c_controller.h>
#include <tactility/log.h>
#include <tactility/error.h>
#include <tactility/freertos/freertos.h>

#include <Tactility/hal/Configuration.h>

using namespace tt::hal;

static constexpr auto* TAG = "ES3C28P";
static constexpr uint8_t ES8311_I2C_ADDR = 0x18;

static error_t initSound(::Device* i2c_controller) {
    static constexpr uint8_t ENABLED_BULK_DATA[] = {
        0x00, 0x80,  // RESET/CSM POWER ON
        0x01, 0x3F,  // CLOCK_MANAGER/ use MCLK pin (external), all clocks on
        0x02, 0x00,  // CLOCK_MANAGER/ pre_div=1 pre_multi=1 (256x MCLK is correct ratio)
        0x0D, 0x01,  // SYSTEM/ Power up analog circuitry
        0x12, 0x00,  // SYSTEM/ power-up DAC
        0x13, 0x10,  // SYSTEM/ Enable output to HP drive
        0x32, 0xBF,  // DAC/ DAC volume (0xBF == ±0 dB)
        0x37, 0x08,  // DAC/ Bypass DAC equalizer
    };

    return i2c_controller_write_register_array(
        i2c_controller,
        ES8311_I2C_ADDR,
        ENABLED_BULK_DATA,
        sizeof(ENABLED_BULK_DATA),
        pdMS_TO_TICKS(1000)
    );
}

static error_t initMicrophone(::Device* i2c_controller) {
    static constexpr uint8_t ENABLED_BULK_DATA[] = {
        0x00, 0x80,  // RESET/CSM POWER ON
        0x01, 0x3F,  // CLOCK_MANAGER/ use MCLK pin (external), all clocks on
        0x02, 0x00,  // CLOCK_MANAGER/ pre_div=1 pre_multi=1
        0x0D, 0x01,  // SYSTEM/ Power up analog circuitry
        0x0E, 0x02,  // SYSTEM/ Enable analog PGA, enable ADC modulator
        0x14, 0x10,  // ADC_REG14: select Mic1p-Mic1n / PGA GAIN (minimum)
        0x17, 0xFF,  // ADC_REG17: ADC_VOLUME (MAXGAIN)
        0x1C, 0x6A,  // ADC_REG1C: ADC Equalizer bypass, cancel DC offset
    };

    return i2c_controller_write_register_array(
        i2c_controller,
        ES8311_I2C_ADDR,
        ENABLED_BULK_DATA,
        sizeof(ENABLED_BULK_DATA),
        pdMS_TO_TICKS(1000)
    );
}

static bool initBoot() {
    // 1. Initialize display backlight
    if (!driver::pwmbacklight::init(LCD_PIN_BACKLIGHT)) {
        return false;
    }

    // 2. Initialize and power on the FM8002E Audio Amplifier (GPIO 1, Active LOW)
    gpio_config_t io_conf = {};
    io_conf.intr_type = GPIO_INTR_DISABLE;
    io_conf.mode = GPIO_MODE_OUTPUT;
    io_conf.pin_bit_mask = (1ULL << GPIO_NUM_1);
    io_conf.pull_down_en = GPIO_PULLDOWN_DISABLE;
    io_conf.pull_up_en = GPIO_PULLUP_DISABLE;
    gpio_config(&io_conf);
    
    // Drive LOW to enable the speaker amplifier
    gpio_set_level(GPIO_NUM_1, 0);

    // 3. Configure the ES8311 Codec over the I2C bus
    auto* i2c_bus = device_find_by_name("i2c0");
    if (i2c_bus != nullptr) {
        error_t error = initSound(i2c_bus);
        if (error != ERROR_NONE) {
            LOG_E(TAG, "Failed to enable ES8311 speaker: %s", error_to_string(error));
        }
        error = initMicrophone(i2c_bus);
        if (error != ERROR_NONE) {
            LOG_E(TAG, "Failed to enable ES8311 microphone: %s", error_to_string(error));
        }
    } else {
        LOG_E(TAG, "i2c0 bus not found, skipping ES8311 initialization");
    }

    return true;
}

static DeviceVector createDevices() {
    return {
        createDisplay()
    };
}

extern const Configuration hardwareConfiguration = {
    .initBoot = initBoot,
    .createDevices = createDevices
};