Ken Van Hoeylandt
d896657bf9
Device migrations: - cyd-4848S040c - guition-jc1060p470ciwy - guition-jc2432w328c - guition-jc3248w535c (known issue with display and touch, Shadowtrance will look into it) - guition-jc8048w550c - heltec-wifi-lora-32-v3 - lilygo-tdeck-max (excluding graphics) - lilygo-tdisplay - lilygo-tdisplay-s3 - lilygo-tdongle-s3 - lilygo-tlora-pager Driver migrations: - Implemented haptic driver interface in kernel - AXS15231b - BQ25896 - BQ27220 - CST328 - CST6xx - DRV2605 - JD9165 - Custom LilyGO driver for T-Lora Pager - SSD1306 - ST7701 - ST7735 - SY6970 - TCA8418 Fixes/improvements: - Boot app: support for multiple power devices, improved UI - lvgl_devices and related code: fixes for mapping - Support for arrays in dts parser
70 lines
2.2 KiB
C
70 lines
2.2 KiB
C
// SPDX-License-Identifier: Apache-2.0
|
|
#pragma once
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#include <stdint.h>
|
|
#include <stdbool.h>
|
|
|
|
#include <tactility/device.h>
|
|
#include <tactility/drivers/gpio.h>
|
|
|
|
struct Jd9165Config {
|
|
uint16_t horizontal_resolution;
|
|
uint16_t vertical_resolution;
|
|
uint8_t bits_per_pixel;
|
|
bool bgr_order;
|
|
bool invert_color;
|
|
bool mirror_x;
|
|
bool mirror_y;
|
|
|
|
// Reset pin for the panel. GPIO_PIN_SPEC_NONE falls back to a software reset sent over the
|
|
// DBI command interface (see esp_lcd_jd9165's panel_jd9165_reset()).
|
|
struct GpioPinSpec pin_reset;
|
|
bool reset_active_high;
|
|
|
|
// LDO channel powering the MIPI DSI PHY - the PHY has no power of its own until this is
|
|
// acquired, so it must happen before the DSI bus is created. Both fields are int32_t (not
|
|
// uint32_t) to exactly match esp_ldo_channel_config_t's plain `int` fields - assigning a
|
|
// uint32_t into that struct's brace-init would be a narrowing conversion (-Werror=narrowing).
|
|
int32_t ldo_channel;
|
|
int32_t ldo_voltage_mv;
|
|
|
|
uint8_t dsi_bus_id;
|
|
// Number of MIPI DSI data lanes. 0 falls back to the maximum available.
|
|
uint8_t num_data_lanes;
|
|
uint32_t lane_bit_rate_mbps;
|
|
|
|
uint32_t dpi_clock_freq_mhz;
|
|
uint32_t hsync_pulse_width;
|
|
uint32_t hsync_back_porch;
|
|
uint32_t hsync_front_porch;
|
|
uint32_t vsync_pulse_width;
|
|
uint32_t vsync_back_porch;
|
|
uint32_t vsync_front_porch;
|
|
// Number of screen-sized frame buffers the driver allocates (0 or 1 = single-buffered).
|
|
uint8_t num_fbs;
|
|
bool use_dma2d;
|
|
bool disable_lp;
|
|
|
|
// See the 'allow-tearing' binding property.
|
|
bool allow_tearing;
|
|
|
|
// Custom vendor init sequence, flattened as bytes: a run of
|
|
// [cmd, data_len, delay_ms, data_len bytes of data...] entries. NULL/0 falls back to the
|
|
// JD9165 component's own built-in default sequence (see vendor_specific_init_default in
|
|
// esp_lcd_jd9165.c) - just a sleep-out + display-on, not guaranteed to match any particular
|
|
// panel's actual bring-up requirements.
|
|
const uint8_t* init_sequence;
|
|
uint32_t init_sequence_length;
|
|
|
|
// Optional reference to this display's backlight device, NULL if none.
|
|
struct Device* backlight;
|
|
};
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|