fix: MCP settings persistence + WebServer/DevServer coexistence + screensaver charging toggle

- McpSettings was hardcoded to /data/service/mcp/settings.properties,
  but ES3C28P uses storage.userDataLocation=SD so user data lives on
  /sdcard/tactility/. Settings appeared to save but on reload returned
  default false -> "enable and when I go back shows disabled".
  Fixed to use getUserDataPath()+"/settings/mcp.properties" pattern
  consistent with DisplaySettings/WebServerSettings, with
  findOrCreateParentDirectory() and isFile() guard.

- HttpServer ctrl_port collision: ESP-IDF default 32768 used by both
  WebServer (80) and DevelopmentService (6666). Second httpd_start()
  failed silently -> dashboard up but /api/mcp 404 and :6666 refused.
  Fixed with unique ctrl_port = 32768 + (port % 1000).
  Added CONFIG_HTTPD_MAX_URI_HANDLERS=20 (default 8 < 9 needed for
  7 handlers + 2 internal).

- DevService stack 5120 -> 8192 for /app/install handling.
- McpSystem video stream task stack 4096 -> 8192 and idle yield 50ms
  (was 5ms always) to avoid CPU starvation blocking httpd tasks.
  On RLCD, timer must always run: DisplayIdle early return on
  !supportsBacklightDuty() broke MCP manual activation (cachedSettings
  not loaded, backlight duty 0). Fixed to always load settings +
  start timer, log RLCD detection, guard setBacklightDuty with
  supportsBacklightDuty() and fallback duty 255.

- DisplaySettings: add disableScreensaverWhenCharging bool, persisted,
  with UI toggle in Display app (Settings->Display) using
  PowerDevice::IsCharging check via findDevices callback.
  When charging and flag enabled, screensaver activation skipped,
  and if already dimmed, wake on charging.

- ES3C28P Power driver: GPIO9 ADC1_CH8 2x divider 2500-4200mV spec from
  ~/Downloads official docs, TP4054 CHRG not connected to GPIO, so
  IsCharging inferred via voltage thresholds (<500mV no battery USB
  or >5000mV wall powered, >=4150mV high) + rising trend.

Verified: flashed es3c28p to /dev/cu.usbmodem101 (192.168.68.113),
WiFi FamReynaMesh RSSI -59, dashboard 200, :6666/info now works,
/api/mcp returns disabled correctly until enabled, persists to SD.

.github/ISSUE_TEMPLATE/bug_report.md

@@ -30,4 +30,4 @@ If applicable, add screenshots to help explain your problem.
 
 **Additional context**
 Add any other context about the problem here.
-Add your oops.tactility.one URL if you had a crash (scanned from QR).
+Add your oops.tactilityproject.org URL if you had a crash (scanned from QR).

.github/PULL_REQUEST_TEMPLATE/pull_request_template.md

@@ -1,7 +1,7 @@
 ### Checklist 
 
-- [ ] I read [contribution guidelines](https://github.com/ByteWelder/Tactility/blob/main/CONTRIBUTING.md)
+- [ ] I read [contribution guidelines](https://github.com/TactilityProject/Tactility/blob/main/CONTRIBUTING.md)
-- [ ] Code adheres to the [coding style](https://github.com/ByteWelder/Tactility/blob/main/CODING_STYLE.md)
+- [ ] Code adheres to the [coding style](https://github.com/TactilityProject/Tactility/blob/main/CODING_STYLE.md)
 
 ### Description
 

.github/actions/build-firmware/action.yml

@@ -16,16 +16,23 @@ runs:
         submodules: recursive
     - name: 'Board select'
       shell: bash
-      run: cp sdkconfig.board.${{ inputs.board_id }} sdkconfig
+      run: python device.py ${{ inputs.board_id }}
     - name: 'Build'
       uses: espressif/esp-idf-ci-action@v1
       with:
-        esp_idf_version: v5.5
+        esp_idf_version: v5.5.2
         target: ${{ inputs.arch }}
         path: './'
     - name: 'Release'
       shell: bash
       run: Buildscripts/release.sh ${{ inputs.board_id }}
+    - name: 'Merge binary'
+      shell: bash
+      run: |
+        python -m pip install esptool
+        cd release/Tactility-${{ inputs.board_id }}
+        bash ./merge.sh ${{ inputs.arch }}
+        mv Binaries/merged_binary.bin ../Tactility-${{ inputs.board_id }}.bin
     - name: 'Upload Artifact: Release'
       uses: actions/upload-artifact@v4
       with:
@@ -38,3 +45,9 @@ runs:
         name: Tactility-${{ inputs.board_id }}-symbols
         path: release/Tactility-${{ inputs.board_id }}-symbols
         retention-days: 30
+    - name: 'Upload Artifact: Merged binary'
+      uses: actions/upload-artifact@v4
+      with:
+        name: Tactility-${{ inputs.board_id }}.bin
+        path: release/Tactility-${{ inputs.board_id }}.bin
+        retention-days: 30

.github/actions/build-sdk/action.yml

@@ -16,20 +16,34 @@ runs:
         submodules: recursive
     - name: 'Board select'
       shell: bash
-      run: cp sdkconfig.board.${{ inputs.board_id }} sdkconfig
+      run: python device.py ${{ inputs.board_id }}
     - name: 'Build'
       uses: espressif/esp-idf-ci-action@v1
       with:
         # NOTE: Update with ESP-IDF!
-        esp_idf_version: v5.5
+        esp_idf_version: v5.5.2
         target: ${{ inputs.arch }}
         path: './'
     - name: 'Release'
       shell: bash
       env:
         # NOTE: Update with ESP-IDF!
-        ESP_IDF_VERSION: '5.5'
+        ESP_IDF_VERSION: '5.5.2'
-      run: Buildscripts/release-sdk.sh release/TactilitySDK
+      run: python Buildscripts/release-sdk.py release/TactilitySDK
+    - name: 'Test Integration Prep'
+      shell: bash
+      # The manifest.properties of our integration test uses version 0.0.0 to indicate that it is not using a normal SDK
+      # This way, it only works with our custom build. That means we have to create a copy of the SDK with the correct folder structure:
+      run: |
+        TACTILITY_SDK_NAME="0.0.0-${{ inputs.arch }}"
+        mkdir -p test_sdk/$TACTILITY_SDK_NAME
+        cp -r release/TactilitySDK test_sdk/$TACTILITY_SDK_NAME
+    - name: 'Test Integration'
+      uses: espressif/esp-idf-ci-action@v1
+      with:
+        esp_idf_version: v5.5.2
+        target: ${{ inputs.arch }}
+        command: export TACTILITY_SDK_PATH=../../test_sdk && cd Tests/SdkIntegration && python tactility.py build ${{ inputs.arch }} --local-sdk
     - name: 'Upload Artifact'
       uses: actions/upload-artifact@v4
       with:

.github/actions/build-simulator/action.yml

@@ -15,7 +15,7 @@ runs:
   using: "composite"
   steps:
     - name: "Checkout repo"
-      uses: actions/checkout@v2
+      uses: actions/checkout@v4
       with:
         submodules: recursive
     - name: Install Linux Dependencies for SDL

.github/actions/bundle-artifacts/action.yml

@@ -0,0 +1,15 @@
+name: Bundle All
+
+runs:
+  using: 'composite'
+  steps:
+    - name: 'Download artifacts'
+      uses: actions/download-artifact@v4
+      with:
+        path: artifacts
+    - name: 'Upload Artifact'
+      uses: actions/upload-artifact@v4
+      with:
+        name: 'all-artifacts'
+        path: artifacts/
+        retention-days: 3

.github/actions/publish-firmware/action.yml

@@ -0,0 +1,24 @@
+name: Publish Firmware
+
+inputs:
+  cdn_version:
+    description: The version that determines the path on the CDN
+    required: true
+
+runs:
+  using: 'composite'
+  steps:
+    - name: 'Download all-artifacts'
+      uses: actions/download-artifact@v4
+      with:
+        name: 'all-artifacts'
+        path: artifacts
+    - name: 'Install boto3'
+      shell: bash
+      run: pip install boto3
+    - name: 'Generate files'
+      shell: bash
+      run: version=`cat version.txt` && python Buildscripts/CDN/generate-firmware-files.py artifacts artifacts-cdn $version
+    - name: 'Upload files'
+      shell: bash
+      run: python Buildscripts/CDN/upload-firmware-files.py artifacts-cdn ${{ inputs.cdn_version }} ${{ env.CDN_ID }} ${{ env.CDN_TOKEN_NAME }} ${{ env.CDN_TOKEN_VALUE }}

.github/actions/publish-sdk/action.yml

@@ -0,0 +1,19 @@
+name: Publish SDK
+
+runs:
+  using: 'composite'
+  steps:
+    - name: 'Download all-artifacts'
+      uses: actions/download-artifact@v4
+      with:
+        name: 'all-artifacts'
+        path: artifacts
+    - name: 'Install boto3'
+      shell: bash
+      run: pip install boto3
+    - name: 'Generate files'
+      shell: bash
+      run: version=`cat version.txt` && python Buildscripts/CDN/generate-sdk-files.py artifacts artifacts-cdn $version
+    - name: 'Upload files'
+      shell: bash
+      run: version=`cat version.txt` && python Buildscripts/CDN/upload-sdk-files.py artifacts-cdn $version ${{ env.CDN_ID }} ${{ env.CDN_TOKEN_NAME }} ${{ env.CDN_TOKEN_VALUE }}

.github/workflows/build-firmware.yml

@@ -1,54 +0,0 @@
-name: Build Firmware
-on:
-  push:
-    branches:
-      - main
-  pull_request:
-    types: [ opened, synchronize, reopened ]
-
-permissions: read-all
-
-jobs:
-  build:
-    strategy:
-      matrix:
-        board: [
-          { id: cyd-2432s024c, arch: esp32 },
-          { id: cyd-2432s028r, arch: esp32 },
-          { id: cyd-2432s028rv3, arch: esp32 },
-          { id: cyd-e32r28t, arch: esp32 },
-          { id: cyd-e32r32p, arch: esp32 },
-          { id: cyd-2432s032c, arch: esp32 },
-          { id: cyd-jc2432w328c, arch: esp32 },
-          { id: cyd-8048s043c, arch: esp32s3 },
-          { id: cyd-jc8048w550c, arch: esp32s3 },
-          { id: cyd-4848s040c, arch: esp32s3 },
-          { id: elecrow-crowpanel-advance-28, arch: esp32s3 },
-          { id: elecrow-crowpanel-advance-35, arch: esp32s3 },
-          { id: elecrow-crowpanel-advance-50, arch: esp32s3 },
-          { id: elecrow-crowpanel-basic-28, arch: esp32 },
-          { id: elecrow-crowpanel-basic-35, arch: esp32 },
-          { id: elecrow-crowpanel-basic-50, arch: esp32s3 },
-          { id: lilygo-tdeck, arch: esp32s3 },
-          { id: lilygo-tdongle-s3, arch: esp32s3 },
-          { id: lilygo-tlora-pager, arch: esp32s3 },
-          { id: m5stack-cardputer, arch: esp32s3 },
-          { id: m5stack-cardputer-adv, arch: esp32s3 },
-          { id: m5stack-core2, arch: esp32 },
-          { id: m5stack-cores3, arch: esp32s3 },
-          { id: m5stack-stickc-plus, arch: esp32 },
-          { id: m5stack-stickc-plus2, arch: esp32 },
-          { id: unphone, arch: esp32s3 },
-          { id: waveshare-s3-touch-lcd-43, arch: esp32s3 },
-          { id: waveshare-s3-touch-lcd-147, arch: esp32s3 },
-          { id: waveshare-s3-touch-lcd-128, arch: esp32s3 },
-          { id: waveshare-s3-lcd-13, arch: esp32s3 }
-        ]
-    runs-on: ubuntu-latest
-    steps:
-      - uses: actions/checkout@v4
-      - name: "Build"
-        uses: ./.github/actions/build-firmware
-        with:
-          board_id: ${{ matrix.board.id }}
-          arch: ${{ matrix.board.arch }}

.github/workflows/build-sdk.yml

@@ -1,26 +0,0 @@
-name: Build SDK
-on:
-  push:
-    branches:
-      - main
-  pull_request:
-    types: [ opened, synchronize, reopened ]
-
-permissions: read-all
-
-jobs:
-  build:
-    strategy:
-      matrix:
-        board: [
-          { id: cyd-2432s028r, arch: esp32 },
-          { id: lilygo-tdeck, arch: esp32s3 },
-        ]
-    runs-on: ubuntu-latest
-    steps:
-      - uses: actions/checkout@v4
-      - name: "Build"
-        uses: ./.github/actions/build-sdk
-        with:
-          board_id: ${{ matrix.board.id }}
-          arch: ${{ matrix.board.arch }}

.github/workflows/build-simulator.yml

@@ -11,6 +11,8 @@ jobs:
     runs-on: ubuntu-24.04
     steps:
       - uses: actions/checkout@v4
+        with:
+          persist-credentials: false
       - name: "Build"
         uses: ./.github/actions/build-simulator
         with:
@@ -21,6 +23,8 @@ jobs:
     runs-on: macos-latest
     steps:
       - uses: actions/checkout@v4
+        with:
+          persist-credentials: false
       - name: "Build"
         uses: ./.github/actions/build-simulator
         with:

.github/workflows/build.yml

@@ -0,0 +1,142 @@
+name: Build Firmware
+on:
+  push:
+    branches:
+      - main
+    tags:
+      - v*
+  pull_request:
+    types: [ opened, synchronize, reopened ]
+
+permissions: read-all
+
+jobs:
+  BuildSdk:
+    strategy:
+      matrix:
+        board: [
+          { id: generic-esp32, arch: esp32 },
+          { id: generic-esp32c6, arch: esp32c6 },
+          { id: generic-esp32p4, arch: esp32p4 },
+          { id: generic-esp32s3, arch: esp32s3 },
+        ]
+    runs-on: ubuntu-latest
+    steps:
+      - uses: actions/checkout@v4
+        with:
+          persist-credentials: false
+      - name: "Build SDK"
+        uses: ./.github/actions/build-sdk
+        with:
+          board_id: ${{ matrix.board.id }}
+          arch: ${{ matrix.board.arch }}
+  BuildFirmware:
+    strategy:
+      matrix:
+        board: [
+          { id: btt-panda-touch, arch: esp32s3 },
+          { id: cyd-2432s024c, arch: esp32 },
+          { id: cyd-2432s024r, arch: esp32 },
+          { id: cyd-2432s028r, arch: esp32 },
+          { id: cyd-2432s028rv3, arch: esp32 },
+          { id: cyd-e32r28t, arch: esp32 },
+          { id: cyd-e32r32p, arch: esp32 },
+          { id: cyd-2432s032c, arch: esp32 },
+          { id: cyd-3248s035c, arch: esp32 },
+          { id: cyd-8048s043c, arch: esp32s3 },
+          { id: cyd-4848s040c, arch: esp32s3 },
+          { id: elecrow-crowpanel-advance-28, arch: esp32s3 },
+          { id: elecrow-crowpanel-advance-35, arch: esp32s3 },
+          { id: elecrow-crowpanel-advance-50, arch: esp32s3 },
+          { id: elecrow-crowpanel-basic-28, arch: esp32 },
+          { id: elecrow-crowpanel-basic-35, arch: esp32 },
+          { id: elecrow-crowpanel-basic-50, arch: esp32s3 },
+          { id: guition-jc1060p470ciwy, arch: esp32p4 },
+          { id: guition-jc2432w328c, arch: esp32 },
+          { id: guition-jc3248w535c, arch: esp32s3 },
+          { id: guition-jc8048w550c, arch: esp32s3 },
+          { id: heltec-wifi-lora-32-v3, arch: esp32s3 },
+          { id: lilygo-tdeck, arch: esp32s3 },
+          { id: lilygo-thmi, arch: esp32s3 },
+          { id: lilygo-tdongle-s3, arch: esp32s3 },
+          { id: lilygo-tdisplay-s3, arch: esp32s3 },
+          { id: lilygo-tlora-pager, arch: esp32s3 },
+          { id: lilygo-tdisplay, arch: esp32 },
+          { id: m5stack-cardputer, arch: esp32s3 },
+          { id: m5stack-cardputer-adv, arch: esp32s3 },
+          { id: m5stack-core2, arch: esp32 },
+          { id: m5stack-cores3, arch: esp32s3 },
+          { id: m5stack-papers3, arch: esp32s3 },
+          { id: m5stack-stackchan, arch: esp32s3 },
+          { id: m5stack-stickc-plus2, arch: esp32 },
+          { id: m5stack-sticks3, arch: esp32s3 },
+          { id: m5stack-tab5, arch: esp32p4 },
+          { id: unphone, arch: esp32s3 },
+          { id: waveshare-esp32-s3-geek, arch: esp32s3 },
+          { id: waveshare-s3-lcd-13, arch: esp32s3 },
+          { id: waveshare-s3-touch-lcd-128, arch: esp32s3 },
+          { id: waveshare-s3-touch-lcd-147, arch: esp32s3 },
+          { id: waveshare-s3-touch-lcd-43, arch: esp32s3 },
+          { id: wireless-tag-wt32-sc01-plus, arch: esp32s3 }
+        ]
+    runs-on: ubuntu-latest
+    needs: [ BuildSdk ]
+    steps:
+      - uses: actions/checkout@v4
+        with:
+          persist-credentials: false
+      - name: "Build Firmware"
+        uses: ./.github/actions/build-firmware
+        with:
+          board_id: ${{ matrix.board.id }}
+          arch: ${{ matrix.board.arch }}
+  BundleArtifacts:
+    runs-on: ubuntu-latest
+    needs: [ BuildFirmware ]
+    if: |
+      (github.event_name == 'push' && github.ref == 'refs/heads/main') ||
+      (github.event_name == 'push' && startsWith(github.ref, 'refs/tags/v'))
+    steps:
+      - uses: actions/checkout@v4
+      - name: "Bundle Artifacts"
+        uses: ./.github/actions/bundle-artifacts
+  PublishFirmwareSnapshot:
+    runs-on: ubuntu-latest
+    needs: [ BundleArtifacts ]
+    if: (github.event_name == 'push' && github.ref == 'refs/heads/main')
+    steps:
+      - uses: actions/checkout@v4
+      - name: "Publish Firmware Snapshot"
+        env:
+          CDN_ID: ${{ secrets.CDN_ID }}
+          CDN_TOKEN_NAME: ${{ secrets.CDN_TOKEN_NAME }}
+          CDN_TOKEN_VALUE: ${{ secrets.CDN_TOKEN_VALUE }}
+        uses: ./.github/actions/publish-firmware
+        with:
+          cdn_version: snapshot
+  PublishFirmwareStable:
+    runs-on: ubuntu-latest
+    needs: [ BundleArtifacts ]
+    if: (github.event_name == 'push' && startsWith(github.ref, 'refs/tags/v'))
+    steps:
+      - uses: actions/checkout@v4
+      - name: "Publish Firmware Stable"
+        env:
+          CDN_ID: ${{ secrets.CDN_ID }}
+          CDN_TOKEN_NAME: ${{ secrets.CDN_TOKEN_NAME }}
+          CDN_TOKEN_VALUE: ${{ secrets.CDN_TOKEN_VALUE }}
+        uses: ./.github/actions/publish-firmware
+        with:
+          cdn_version: stable
+  PublishSdk:
+    runs-on: ubuntu-latest
+    needs: [ BundleArtifacts ]
+    if: (github.event_name == 'push' && (github.ref == 'refs/heads/main' || startsWith(github.ref, 'refs/tags/v')))
+    steps:
+      - uses: actions/checkout@v4
+      - name: "Publish SDKs"
+        env:
+          CDN_ID: ${{ secrets.CDN_ID }}
+          CDN_TOKEN_NAME: ${{ secrets.CDN_TOKEN_NAME }}
+          CDN_TOKEN_VALUE: ${{ secrets.CDN_TOKEN_VALUE }}
+        uses: ./.github/actions/publish-sdk

.github/workflows/tests.yml

@@ -4,13 +4,13 @@ on:
     branches:
       - main
   pull_request:
-    types: [opened, synchronize, reopened]
+    types: [ opened, synchronize, reopened ]
 jobs:
-  run:
+  TactilityTests:
     runs-on: ubuntu-latest
     steps:
       - name: "Checkout repo"
-        uses: actions/checkout@v2
+        uses: actions/checkout@v4
         with:
           submodules: recursive
       - name: "Configure Project"
@@ -20,6 +20,25 @@ jobs:
       - name: "Build Tests"
         run: cmake --build build --target build-tests
       - name: "Run TactilityCore Tests"
-        run: build/Tests/TactilityCore/TactilityCoreTests --exit
+        run: build/Tests/TactilityCore/TactilityCoreTests
+      - name: "Run TactilityFreeRtos Tests"
+        run: build/Tests/TactilityFreeRtos/TactilityFreeRtosTests
       - name: "Run TactilityHeadless Tests"
-        run: build/Tests/Tactility/TactilityTests --exit
+        run: build/Tests/Tactility/TactilityTests
+      - name: "Run TactilityKernel Tests"
+        run: build/Tests/TactilityKernel/TactilityKernelTests
+  DevicetreeTests:
+    runs-on: ubuntu-latest
+    steps:
+      - name: "Checkout repo"
+      - uses: actions/checkout@v4
+        with:
+          persist-credentials: false
+          submodules: recursive
+      - name: "Install Python Dependencies"
+        shell: bash
+        run: pip install lark==1.3.1 pyyaml==6.0.3
+      - name: "Run Devicetree Tests"
+        shell: bash
+        working-directory: Buildscripts/DevicetreeCompiler/tests
+        run: python test_integration.py

.gitignore

@@ -3,8 +3,7 @@
 
 build/
 buildsim/
-build-sim/
+cmake-*/
-cmake-build-*/
 CMakeCache.txt
 *.cbp
 CMakeFiles
@@ -18,6 +17,12 @@ managed_components/
 dependencies.lock
 
 .vscode/
+*.code-workspace
 .gitpod.yml
 
-sdkconfig.board.*.dev
+sdkconfig.board.*.dev
+
+.tactility/
+
+.caveman.json
+.ai/mcp

Boards/cyd-2432s024c/Source/Configuration.cpp

@@ -1,116 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <PwmBacklight.h>
-
-static bool initBoot() {
-    // Set the RGB LED Pins to output and turn them off
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_4, GPIO_MODE_OUTPUT)); // Red
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_16, GPIO_MODE_OUTPUT)); // Green
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_17, GPIO_MODE_OUTPUT)); // Blue
-
-    // 0 on, 1 off
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_4, 1)); // Red
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_16, 1)); // Green
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_17, 1)); // Blue
-
-    return driver::pwmbacklight::init(LCD_PIN_BACKLIGHT);
-}
-
-static tt::hal::DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const tt::hal::Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        tt::hal::i2c::Configuration {
-            .name = "First",
-            .port = I2C_NUM_0,
-            .initMode = tt::hal::i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_33,
-                .scl_io_num = GPIO_NUM_32,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-        tt::hal::i2c::Configuration {
-            .name = "Second",
-            .port = I2C_NUM_1,
-            .initMode = tt::hal::i2c::InitMode::Disabled,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_NC,
-                .scl_io_num = GPIO_NUM_NC,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        tt::hal::spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_NC,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC, // Quad SPI LCD driver is not yet supported
-                .quadhd_io_num = GPIO_NUM_NC, // Quad SPI LCD driver is not yet supported
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = tt::hal::spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-        tt::hal::spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC, // Quad SPI LCD driver is not yet supported
-                .quadhd_io_num = GPIO_NUM_NC, // Quad SPI LCD driver is not yet supported
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 8192,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = tt::hal::spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr
-        },
-    }
-};

Boards/cyd-2432s024c/Source/devices/Display.h

@@ -1,19 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/display/DisplayDevice.h>
-#include <driver/gpio.h>
-#include <driver/spi_common.h>
-#include <memory>
-
-// Display
-constexpr auto LCD_PIN_BACKLIGHT = GPIO_NUM_27;
-constexpr auto LCD_SPI_HOST = SPI2_HOST;
-constexpr auto LCD_PIN_CS = GPIO_NUM_15;
-constexpr auto LCD_PIN_DC = GPIO_NUM_2;
-constexpr auto LCD_HORIZONTAL_RESOLUTION = 240;
-constexpr auto LCD_VERTICAL_RESOLUTION = 320;
-constexpr auto LCD_BUFFER_HEIGHT = LCD_VERTICAL_RESOLUTION / 10;
-constexpr auto LCD_BUFFER_SIZE = LCD_HORIZONTAL_RESOLUTION * LCD_BUFFER_HEIGHT;
-constexpr auto LCD_SPI_TRANSFER_SIZE_LIMIT = LCD_BUFFER_SIZE * LV_COLOR_DEPTH / 8;
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/cyd-2432s024c/Source/devices/SdCard.cpp

@@ -1,28 +0,0 @@
-#include "SdCard.h"
-
-#define TAG "twodotfour_sdcard"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-constexpr auto SDCARD_SPI_HOST = SPI3_HOST;
-constexpr auto SDCARD_PIN_CS = GPIO_NUM_5;
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        SDCARD_PIN_CS,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        std::make_shared<tt::Mutex>(tt::Mutex::Type::Recursive),
-        std::vector<gpio_num_t>(),
-        SDCARD_SPI_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}
-

Boards/cyd-2432s024c/Source/devices/SdCard.h

@@ -1,8 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();
-

Boards/cyd-2432s028r/Source/Configuration.cpp

@@ -1,129 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <PwmBacklight.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    // Set the RGB LED Pins to output and turn them off
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_4, GPIO_MODE_OUTPUT)); // Red
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_16, GPIO_MODE_OUTPUT)); // Green
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_17, GPIO_MODE_OUTPUT)); // Blue
-
-    // 0 on, 1 off
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_4, 1)); // Red
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_16, 1)); // Green
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_17, 1)); // Blue
-
-    return driver::pwmbacklight::init(LCD_PIN_BACKLIGHT);
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        i2c::Configuration {
-            .name = "CN1",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_27,
-                .scl_io_num = GPIO_NUM_22,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // Display
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_12,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock()
-        },
-        // SDCard
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 0,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-    },
-
-    .uart {
-        uart::Configuration {
-            .name = "P1",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_1,
-            .txPin = GPIO_NUM_3,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/cyd-2432s028r/Source/devices/Display.h

@@ -1,28 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/display/DisplayDevice.h>
-#include <driver/gpio.h>
-#include <driver/spi_common.h>
-#include <memory>
-
-// Display
-constexpr auto LCD_SPI_HOST = SPI2_HOST;
-constexpr auto LCD_PIN_CS = GPIO_NUM_15;
-constexpr auto LCD_PIN_DC = GPIO_NUM_2;
-constexpr auto LCD_HORIZONTAL_RESOLUTION = 240;
-constexpr auto LCD_VERTICAL_RESOLUTION = 320;
-constexpr auto LCD_BUFFER_HEIGHT = LCD_VERTICAL_RESOLUTION / 10;
-constexpr auto LCD_BUFFER_SIZE = LCD_HORIZONTAL_RESOLUTION * LCD_BUFFER_HEIGHT;
-constexpr auto LCD_SPI_TRANSFER_SIZE_LIMIT = LCD_BUFFER_SIZE * LV_COLOR_DEPTH / 8;
-
-// Display backlight (PWM)
-constexpr auto LCD_PIN_BACKLIGHT = GPIO_NUM_21;
-
-// Touch (Software SPI)
-constexpr auto TOUCH_MISO_PIN = GPIO_NUM_39;
-constexpr auto TOUCH_MOSI_PIN = GPIO_NUM_32;
-constexpr auto TOUCH_SCK_PIN = GPIO_NUM_25;
-constexpr auto TOUCH_CS_PIN = GPIO_NUM_33;
-constexpr auto TOUCH_IRQ_PIN = GPIO_NUM_36;
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/cyd-2432s028r/Source/devices/SdCard.cpp

@@ -1,21 +0,0 @@
-#include "SdCard.h"
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto config = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_5,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        std::make_shared<tt::Mutex>(tt::Mutex::Type::Recursive),
-        std::vector<gpio_num_t>(),
-        SPI3_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(std::move(config));
-}
-

Boards/cyd-2432s028r/Source/devices/SdCard.h

@@ -1,8 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();
-

Boards/cyd-2432s028rv3/Source/Configuration.cpp

@@ -1,129 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <PwmBacklight.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    // Set the RGB LED Pins to output and turn them off
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_4, GPIO_MODE_OUTPUT)); // Red
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_16, GPIO_MODE_OUTPUT)); // Green
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_17, GPIO_MODE_OUTPUT)); // Blue
-
-    // 0 on, 1 off
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_4, 1)); // Red
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_16, 1)); // Green
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_17, 1)); // Blue
-
-    return driver::pwmbacklight::init(LCD_PIN_BACKLIGHT);
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        i2c::Configuration {
-            .name = "CN1",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_27,
-                .scl_io_num = GPIO_NUM_22,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // Display
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_12,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock()
-        },
-        // SDCard
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 0,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-    },
-
-    .uart {
-        uart::Configuration {
-            .name = "P1",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_1,
-            .txPin = GPIO_NUM_3,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/cyd-2432s028rv3/Source/devices/Display.cpp

@@ -1,49 +0,0 @@
-#include "Display.h"
-#include "Xpt2046SoftSpi.h"
-#include <St7789Display.h>
-#include <PwmBacklight.h>
-
-constexpr auto* TAG = "CYD";
-
-static std::shared_ptr<tt::hal::touch::TouchDevice> createTouch() {
-    auto configuration = std::make_unique<Xpt2046SoftSpi::Configuration>(
-        TOUCH_MOSI_PIN,
-        TOUCH_MISO_PIN,
-        TOUCH_SCK_PIN,
-        TOUCH_CS_PIN,
-        LCD_HORIZONTAL_RESOLUTION,
-        LCD_VERTICAL_RESOLUTION,
-        false, // swapXY
-        true, // mirrorX
-        false // mirrorY
-    );
-
-    return std::make_shared<Xpt2046SoftSpi>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    St7789Display::Configuration panel_configuration = {
-        .horizontalResolution = LCD_HORIZONTAL_RESOLUTION,
-        .verticalResolution = LCD_VERTICAL_RESOLUTION,
-        .gapX = 0,
-        .gapY = 0,
-        .swapXY = false,
-        .mirrorX = false,
-        .mirrorY = false,
-        .invertColor = false,
-        .bufferSize = LCD_BUFFER_SIZE,
-        .touch = createTouch(),
-        .backlightDutyFunction = driver::pwmbacklight::setBacklightDuty,
-        .resetPin = GPIO_NUM_NC
-    };
-
-    auto spi_configuration = std::make_shared<St7789Display::SpiConfiguration>(St7789Display::SpiConfiguration {
-        .spiHostDevice = LCD_SPI_HOST,
-        .csPin = LCD_PIN_CS,
-        .dcPin = LCD_PIN_DC,
-        .pixelClockFrequency = 62'500'000,
-        .transactionQueueDepth = 10
-    });
-
-    return std::make_shared<St7789Display>(panel_configuration, spi_configuration);
-}

Boards/cyd-2432s028rv3/Source/devices/Display.h

@@ -1,28 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/display/DisplayDevice.h>
-
-#include <driver/gpio.h>
-#include <driver/spi_common.h>
-
-#include <memory>
-
-// Display
-constexpr auto LCD_SPI_HOST = SPI2_HOST;
-constexpr auto LCD_PIN_CS = GPIO_NUM_15;
-constexpr auto LCD_PIN_DC = GPIO_NUM_2;
-constexpr auto LCD_PIN_BACKLIGHT = GPIO_NUM_21;
-constexpr auto LCD_HORIZONTAL_RESOLUTION = 240;
-constexpr auto LCD_VERTICAL_RESOLUTION = 320;
-constexpr auto LCD_BUFFER_HEIGHT = LCD_VERTICAL_RESOLUTION / 10;
-constexpr auto LCD_BUFFER_SIZE = LCD_HORIZONTAL_RESOLUTION * LCD_BUFFER_HEIGHT;
-constexpr auto LCD_SPI_TRANSFER_SIZE_LIMIT = LCD_BUFFER_SIZE * LV_COLOR_DEPTH / 8;
-
-// Touch (Software SPI)
-constexpr auto TOUCH_MISO_PIN = GPIO_NUM_39;
-constexpr auto TOUCH_MOSI_PIN = GPIO_NUM_32;
-constexpr auto TOUCH_SCK_PIN = GPIO_NUM_25;
-constexpr auto TOUCH_CS_PIN = GPIO_NUM_33;
-constexpr auto TOUCH_IRQ_PIN = GPIO_NUM_36;
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/cyd-2432s028rv3/Source/devices/SdCard.cpp

@@ -1,21 +0,0 @@
-#include "SdCard.h"
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto config = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_5,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        std::make_shared<tt::Mutex>(tt::Mutex::Type::Recursive),
-        std::vector<gpio_num_t>(),
-        SPI3_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(std::move(config));
-}
-

Boards/cyd-2432s028rv3/Source/devices/SdCard.h

@@ -1,8 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();
-

Boards/cyd-2432s032c/Source/Configuration.cpp

@@ -1,117 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/kernel/SystemEvents.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-#include <PwmBacklight.h>
-
-bool initBoot() {
-    if (!driver::pwmbacklight::init(LCD_PIN_BACKLIGHT)) {
-        return false;
-    }
-
-    // Set the RGB LED Pins to output and turn them off
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_4, GPIO_MODE_OUTPUT)); // Red
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_16, GPIO_MODE_OUTPUT)); // Green
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_17, GPIO_MODE_OUTPUT)); // Blue
-
-    // 0 on, 1 off
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_4, 1)); // Red
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_16, 1)); // Green
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_17, 1)); // Blue
-
-    // This display has a weird glitch with gamma during boot, which results in uneven dark gray colours.
-    // Setting gamma curve index to 0 doesn't work at boot for an unknown reason, so we set the curve index to 1:
-    tt::kernel::subscribeSystemEvent(tt::kernel::SystemEvent::BootSplash, [](auto) {
-        auto display = tt::hal::findFirstDevice<tt::hal::display::DisplayDevice>(tt::hal::Device::Type::Display);
-        assert(display != nullptr);
-        tt::lvgl::lock(portMAX_DELAY);
-        display->setGammaCurve(1U);
-        tt::lvgl::unlock();
-    });
-
-    return true;
-}
-
-static tt::hal::DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const tt::hal::Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        tt::hal::i2c::Configuration {
-            .name = "Internal",
-            .port = I2C_NUM_0,
-            .initMode = tt::hal::i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_33,
-                .scl_io_num = GPIO_NUM_32,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // Display
-        tt::hal::spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_NC,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = tt::hal::spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-        // SD card
-        tt::hal::spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 0,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = tt::hal::spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr
-        },
-    }
-};

Boards/cyd-2432s032c/Source/devices/Display.cpp

@@ -1,44 +0,0 @@
-#include "Display.h"
-
-#include <Gt911Touch.h>
-#include <Ili934xDisplay.h>
-#include <PwmBacklight.h>
-
-static std::shared_ptr<tt::hal::touch::TouchDevice> createTouch() {
-    auto configuration = std::make_unique<Gt911Touch::Configuration>(
-        I2C_NUM_0,
-        LCD_HORIZONTAL_RESOLUTION,
-        LCD_VERTICAL_RESOLUTION
-    );
-
-    return std::make_shared<Gt911Touch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    Ili934xDisplay::Configuration panel_configuration = {
-        .horizontalResolution = LCD_HORIZONTAL_RESOLUTION,
-        .verticalResolution = LCD_VERTICAL_RESOLUTION,
-        .gapX = 0,
-        .gapY = 0,
-        .swapXY = true,
-        .mirrorX = true,
-        .mirrorY = true,
-        .invertColor = true,
-        .swapBytes = true,
-        .bufferSize = LCD_BUFFER_SIZE,
-        .touch = createTouch(),
-        .backlightDutyFunction = driver::pwmbacklight::setBacklightDuty,
-        .resetPin = GPIO_NUM_NC,
-        .rgbElementOrder = LCD_RGB_ELEMENT_ORDER_RGB
-    };
-
-    auto spi_configuration = std::make_shared<Ili934xDisplay::SpiConfiguration>(Ili934xDisplay::SpiConfiguration {
-        .spiHostDevice = LCD_SPI_HOST,
-        .csPin = LCD_PIN_CS,
-        .dcPin = LCD_PIN_DC,
-        .pixelClockFrequency = 40'000'000,
-        .transactionQueueDepth = 10
-    });
-
-    return std::make_shared<Ili934xDisplay>(panel_configuration, spi_configuration, true);
-}

Boards/cyd-2432s032c/Source/devices/Display.h

@@ -1,19 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/display/DisplayDevice.h>
-#include <driver/gpio.h>
-#include <driver/spi_common.h>
-#include <memory>
-
-// Display
-constexpr auto LCD_SPI_HOST = SPI2_HOST;
-constexpr auto LCD_PIN_CS = GPIO_NUM_15;
-constexpr auto LCD_PIN_DC = GPIO_NUM_2;
-constexpr auto LCD_PIN_BACKLIGHT = GPIO_NUM_27;
-constexpr auto LCD_HORIZONTAL_RESOLUTION = 240;
-constexpr auto LCD_VERTICAL_RESOLUTION = 320;
-constexpr auto LCD_BUFFER_HEIGHT = LCD_VERTICAL_RESOLUTION / 10;
-constexpr auto LCD_BUFFER_SIZE = LCD_HORIZONTAL_RESOLUTION * LCD_BUFFER_HEIGHT;
-constexpr auto LCD_SPI_TRANSFER_SIZE_LIMIT = LCD_BUFFER_SIZE * LV_COLOR_DEPTH / 8;
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/cyd-2432s032c/Source/devices/SdCard.cpp

@@ -1,27 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-constexpr auto SDCARD_SPI_HOST = SPI3_HOST;
-constexpr auto SDCARD_PIN_CS = GPIO_NUM_5;
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        SDCARD_PIN_CS,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        std::make_shared<tt::Mutex>(tt::Mutex::Type::Recursive),
-        std::vector<gpio_num_t>(),
-        SDCARD_SPI_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}
-

Boards/cyd-2432s032c/Source/devices/SdCard.h

@@ -1,8 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/sdcard/SdCardDevice.h>
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();
-

Boards/cyd-4848s040c/Source/Configuration.cpp

@@ -1,89 +0,0 @@
-#include "devices/St7701Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/kernel/SystemEvents.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <PwmBacklight.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    return driver::pwmbacklight::init(GPIO_NUM_38, 1000);
-}
-
-static DeviceVector createDevices() {
-    return {
-        std::make_shared<St7701Display>(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        //Touch
-        i2c::Configuration {
-            .name = "Internal",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_19,
-                .scl_io_num = GPIO_NUM_45,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-        //H1 header, 
-        i2c::Configuration {
-            .name = "External",
-            .port = I2C_NUM_1,
-            .initMode = i2c::InitMode::Disabled,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_NC,
-                .scl_io_num = GPIO_NUM_NC,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // SD Card & display init
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_47,
-                .miso_io_num = GPIO_NUM_41,
-                .sclk_io_num = GPIO_NUM_48,
-                .quadwp_io_num = -1,
-                .quadhd_io_num = GPIO_NUM_42,
-                .data4_io_num = -1,
-                .data5_io_num = -1,
-                .data6_io_num = -1,
-                .data7_io_num = -1,
-                .data_io_default_level = false,
-                .max_transfer_sz = 1024 * 128,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock()
-        }
-    }
-};

Boards/cyd-4848s040c/Source/devices/SdCard.cpp

@@ -1,25 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto config = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_42,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        tt::lvgl::getSyncLock(),
-        std::vector { GPIO_NUM_39 }
-    );
-
-    auto sdcard = std::make_shared<SpiSdCardDevice>(
-        std::move(config)
-    );
-
-    return std::static_pointer_cast<SdCardDevice>(sdcard);
-}
-

Boards/cyd-4848s040c/Source/devices/SdCard.h

@@ -1,8 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();
-

Boards/cyd-8048s043c/Source/Configuration.cpp

@@ -1,114 +0,0 @@
-#include "PwmBacklight.h"
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    // Display backlight
-    return driver::pwmbacklight::init(GPIO_NUM_2, 200);
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        // Touch
-        i2c::Configuration {
-            .name = "Internal",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_19,
-                .scl_io_num = GPIO_NUM_20,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-        // P4 header, JST SH 1.0, GND / 3.3V / IO17 / IO18
-        i2c::Configuration {
-            .name = "External",
-            .port = I2C_NUM_1,
-            .initMode = i2c::InitMode::Disabled,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_17,
-                .scl_io_num = GPIO_NUM_18,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // SD Card
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_11,
-                .miso_io_num = GPIO_NUM_13,
-                .sclk_io_num = GPIO_NUM_12,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 8192,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr
-        }
-    },
-    .uart {
-        // P4 header, JST SH 1.0, GND / 3.3V / IO17 / IO18
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_17,
-            .txPin = GPIO_NUM_18,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 9600,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/cyd-8048s043c/Source/devices/Display.cpp

@@ -1,105 +0,0 @@
-#include "Display.h"
-
-#include <Gt911Touch.h>
-#include <PwmBacklight.h>
-#include <RgbDisplay.h>
-#include <Tactility/Log.h>
-
-std::shared_ptr<tt::hal::touch::TouchDevice> _Nullable createTouch() {
-    // Note for future changes: Reset pin is 38 and interrupt pin is 18
-    // or INT = NC, schematic and other info floating around is kinda conflicting...
-    auto configuration = std::make_unique<Gt911Touch::Configuration>(
-        I2C_NUM_0,
-        800,
-        480
-    );
-
-    return std::make_shared<Gt911Touch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    auto touch = createTouch();
-
-    constexpr uint32_t bufferPixels = 800 * 10;
-
-    esp_lcd_rgb_panel_config_t rgb_panel_config = {
-        .clk_src = LCD_CLK_SRC_DEFAULT,
-        .timings = {
-            .pclk_hz = 16000000,
-            .h_res = 800,
-            .v_res = 480,
-            .hsync_pulse_width = 4,
-            .hsync_back_porch = 8,
-            .hsync_front_porch = 8,
-            .vsync_pulse_width = 4,
-            .vsync_back_porch = 8,
-            .vsync_front_porch = 8,
-            .flags = {
-                .hsync_idle_low = false,
-                .vsync_idle_low = false,
-                .de_idle_high = false,
-                .pclk_active_neg = true,
-                .pclk_idle_high = false
-            }
-        },
-        .data_width = 16,
-        .bits_per_pixel = 0,
-        .num_fbs = 2,
-        .bounce_buffer_size_px = bufferPixels,
-        .sram_trans_align = 8,
-        .psram_trans_align = 64,
-        .hsync_gpio_num = GPIO_NUM_39,
-        .vsync_gpio_num = GPIO_NUM_41,
-        .de_gpio_num = GPIO_NUM_40 ,
-        .pclk_gpio_num = GPIO_NUM_42,
-        .disp_gpio_num = GPIO_NUM_NC,
-        .data_gpio_nums = {
-            GPIO_NUM_8, // B3
-            GPIO_NUM_3, // B4
-            GPIO_NUM_46, // B5
-            GPIO_NUM_9, // B6
-            GPIO_NUM_1, // B7
-            GPIO_NUM_5, // G2
-            GPIO_NUM_6, // G3
-            GPIO_NUM_7, // G4
-            GPIO_NUM_15, // G5
-            GPIO_NUM_16, // G6
-            GPIO_NUM_4, // G7
-            GPIO_NUM_45, // R3
-            GPIO_NUM_48, // R4
-            GPIO_NUM_47, // R5
-            GPIO_NUM_21, // R6
-            GPIO_NUM_14, // R7
-        },
-        .flags = {
-            .disp_active_low = false,
-            .refresh_on_demand = false,
-            .fb_in_psram = true,
-            .double_fb = true,
-            .no_fb = false,
-            .bb_invalidate_cache = false
-        }
-    };
-
-    RgbDisplay::BufferConfiguration buffer_config = {
-        .size = (800 * 480),
-        .useSpi = true,
-        .doubleBuffer = true,
-        .bounceBufferMode = true,
-        .avoidTearing = false
-    };
-
-    auto configuration = std::make_unique<RgbDisplay::Configuration>(
-        rgb_panel_config,
-        buffer_config,
-        touch,
-        LV_COLOR_FORMAT_RGB565,
-        false,
-        false,
-        false,
-        false,
-        driver::pwmbacklight::setBacklightDuty
-    );
-
-    return std::make_shared<RgbDisplay>(std::move(configuration));
-}

Boards/cyd-8048s043c/Source/devices/SdCard.cpp

@@ -1,22 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto config = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_10,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot
-    );
-
-    auto sdcard = std::make_shared<SpiSdCardDevice>(
-        std::move(config)
-    );
-
-    return std::static_pointer_cast<SdCardDevice>(sdcard);
-}

Boards/cyd-8048s043c/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/cyd-e32r28t/Source/Configuration.cpp

@@ -1,72 +0,0 @@
-#include "devices/SdCard.h"
-#include "devices/Display.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <PwmBacklight.h>
-
-static bool initBoot() {
-    return driver::pwmbacklight::init(LCD_BACKLIGHT_PIN);
-}
-
-static tt::hal::DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const tt::hal::Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {},
-    .spi = {
-        tt::hal::spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_12,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = tt::hal::spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock()
-        },
-        tt::hal::spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 0,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = tt::hal::spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock()
-        },
-
-    }
-};

Boards/cyd-e32r28t/Source/devices/Display.h

@@ -1,28 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/display/DisplayDevice.h>
-#include <driver/gpio.h>
-#include <driver/spi_common.h>
-#include <memory>
-
-// Display
-constexpr auto LCD_SPI_HOST = SPI2_HOST;
-constexpr auto LCD_PIN_CS = GPIO_NUM_15;
-constexpr auto LCD_PIN_DC = GPIO_NUM_2;
-constexpr auto LCD_HORIZONTAL_RESOLUTION = 240;
-constexpr auto LCD_VERTICAL_RESOLUTION = 320;
-constexpr auto LCD_BUFFER_HEIGHT = (LCD_VERTICAL_RESOLUTION / 10);
-constexpr auto LCD_BUFFER_SIZE = (LCD_HORIZONTAL_RESOLUTION * LCD_BUFFER_HEIGHT);
-constexpr auto LCD_SPI_TRANSFER_SIZE_LIMIT = LCD_BUFFER_SIZE * LV_COLOR_DEPTH / 8;
-
-// Touch (Software SPI)
-constexpr auto TOUCH_MISO_PIN = GPIO_NUM_39;
-constexpr auto TOUCH_MOSI_PIN = GPIO_NUM_32;
-constexpr auto TOUCH_SCK_PIN = GPIO_NUM_25;
-constexpr auto TOUCH_CS_PIN = GPIO_NUM_33;
-constexpr auto TOUCH_IRQ_PIN = GPIO_NUM_36;
-
-// Backlight
-constexpr auto LCD_BACKLIGHT_PIN = GPIO_NUM_21;
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/cyd-e32r28t/Source/devices/SdCard.cpp

@@ -1,21 +0,0 @@
-#include "SdCard.h"
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_5,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        std::make_shared<tt::Mutex>(tt::Mutex::Type::Recursive),
-        std::vector<gpio_num_t>(),
-        SPI3_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/cyd-e32r28t/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/sdcard/SdCardDevice.h>
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/cyd-e32r32p/Source/Configuration.cpp

@@ -1,96 +0,0 @@
-#include "devices/SdCard.h"
-#include "devices/Display.h"
-#include "devices/Power.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <PwmBacklight.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    return driver::pwmbacklight::init(DISPLAY_BACKLIGHT_PIN);
-}
-
-static tt::hal::DeviceVector createDevices() {
-    return {
-        createPower(),
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        tt::hal::i2c::Configuration {
-            .name = "External",
-            .port = I2C_NUM_0,
-            .initMode = tt::hal::i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_32,
-                .scl_io_num = GPIO_NUM_25,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-    },
-    // Display
-    .spi = {
-        tt::hal::spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_12,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = DISPLAY_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = tt::hal::spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock()
-        },
-        // SD Card
-        tt::hal::spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 8192,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = tt::hal::spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr
-        },
-
-    }
-};

Boards/cyd-e32r32p/Source/devices/Display.cpp

@@ -1,51 +0,0 @@
-#include "Display.h"
-
-#include <Xpt2046Touch.h>
-#include <St7789Display.h>
-#include <PwmBacklight.h>
-#include <Tactility/hal/touch/TouchDevice.h>
-
-// Create the XPT2046 touch device (hardware/esp_lcd driver)
-static std::shared_ptr<tt::hal::touch::TouchDevice> createTouch() {
-    auto config = std::make_unique<Xpt2046Touch::Configuration>(
-        DISPLAY_SPI_HOST,                                // spi device / bus (SPI2_HOST)
-        TOUCH_CS_PIN,                                    // touch CS (IO33)
-        (uint16_t)DISPLAY_HORIZONTAL_RESOLUTION,         // x max
-        (uint16_t)DISPLAY_VERTICAL_RESOLUTION,           // y max
-        false,                                               // swapXy
-        true,                                                // mirrorX
-        true                                                 // mirrorY
-    );
-
-    return std::make_shared<Xpt2046Touch>(std::move(config));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    // Create the ST7789 panel configuration
-    St7789Display::Configuration panel_configuration = {
-        .horizontalResolution = DISPLAY_HORIZONTAL_RESOLUTION,
-        .verticalResolution = DISPLAY_VERTICAL_RESOLUTION,
-        .gapX = 0,
-        .gapY = 0,
-        .swapXY = false,
-        .mirrorX = false,
-        .mirrorY = false,
-        .invertColor = false,
-        .bufferSize = DISPLAY_DRAW_BUFFER_SIZE,  // 0 -> default 1/10 screen
-        .touch = createTouch(),
-        .backlightDutyFunction = driver::pwmbacklight::setBacklightDuty,
-        .resetPin = GPIO_NUM_NC,
-        .rgbElementOrder = LCD_RGB_ELEMENT_ORDER_BGR  // BGR for this display
-    };
-
-    // Create the SPI configuration (from EspLcdSpiDisplay base class)
-    auto spi_configuration = std::make_shared<EspLcdSpiDisplay::SpiConfiguration>(EspLcdSpiDisplay::SpiConfiguration {
-        .spiHostDevice = DISPLAY_SPI_HOST,
-        .csPin = DISPLAY_PIN_CS,
-        .dcPin = DISPLAY_PIN_DC,
-        .pixelClockFrequency = 40'000'000,
-        .transactionQueueDepth = 10
-    });
-
-    return std::make_shared<St7789Display>(panel_configuration, spi_configuration);
-}

Boards/cyd-e32r32p/Source/devices/Display.h

@@ -1,27 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/display/DisplayDevice.h>
-#include "driver/gpio.h"
-#include "driver/spi_common.h"
-#include <memory>
-
-// Display (ST7789P3 on this board)
-constexpr auto DISPLAY_SPI_HOST = SPI2_HOST;
-constexpr auto DISPLAY_PIN_CS = GPIO_NUM_15;
-constexpr auto DISPLAY_PIN_DC = GPIO_NUM_2;
-constexpr auto DISPLAY_HORIZONTAL_RESOLUTION = 240;
-constexpr auto DISPLAY_VERTICAL_RESOLUTION = 320;
-constexpr auto DISPLAY_DRAW_BUFFER_HEIGHT = (DISPLAY_VERTICAL_RESOLUTION / 10);
-constexpr auto DISPLAY_DRAW_BUFFER_SIZE = (DISPLAY_HORIZONTAL_RESOLUTION * DISPLAY_DRAW_BUFFER_HEIGHT);
-constexpr auto DISPLAY_BACKLIGHT_PIN = GPIO_NUM_27;
-constexpr auto DISPLAY_SPI_TRANSFER_SIZE_LIMIT = DISPLAY_DRAW_BUFFER_SIZE * sizeof(lv_color_t);
-
-// Touch (XPT2046, resistive, shared SPI with display)
-constexpr auto TOUCH_MISO_PIN = GPIO_NUM_12;
-constexpr auto TOUCH_MOSI_PIN = GPIO_NUM_13;
-constexpr auto TOUCH_SCK_PIN = GPIO_NUM_14;
-constexpr auto TOUCH_CS_PIN = GPIO_NUM_33;
-constexpr auto TOUCH_IRQ_PIN = GPIO_NUM_36;
-
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/cyd-e32r32p/Source/devices/SdCard.cpp

@@ -1,22 +0,0 @@
-#include "SdCard.h"
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-using SdCardDevice = tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        SD_CS_PIN,                         // CS pin (IO5 on the module)
-        GPIO_NUM_NC,                           // MOSI override: leave NC to use SPI host pins
-        GPIO_NUM_NC,                           // MISO override: leave NC
-        GPIO_NUM_NC,                           // SCLK override: leave NC
-        SdCardDevice::MountBehaviour::AtBoot,
-        std::make_shared<tt::Mutex>(tt::Mutex::Type::Recursive),
-        std::vector<gpio_num_t>(),
-        SD_SPI_HOST                        // SPI host for SD card (SPI3_HOST)
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/cyd-e32r32p/Source/devices/SdCard.h

@@ -1,13 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/sdcard/SdCardDevice.h>
-#include "driver/gpio.h"
-#include "driver/spi_common.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-// SD card (microSD)
-constexpr auto SD_CS_PIN = GPIO_NUM_5;
-constexpr auto SD_SPI_HOST = SPI3_HOST;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/cyd-jc2432w328c/Source/Configuration.cpp

@@ -1,148 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <PwmBacklight.h>
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    //Set the RGB Led Pins to output and turn them off
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_4, GPIO_MODE_OUTPUT)); //Red
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_16, GPIO_MODE_OUTPUT)); //Green
-    ESP_ERROR_CHECK(gpio_set_direction(GPIO_NUM_17, GPIO_MODE_OUTPUT)); //Blue
-
-    //0 on, 1 off... yep it's backwards.
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_4, 1)); //Red
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_16, 1)); //Green
-    ESP_ERROR_CHECK(gpio_set_level(GPIO_NUM_17, 1)); //Blue
-
-    return driver::pwmbacklight::init(LCD_PIN_BACKLIGHT);
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        //Touch
-        i2c::Configuration {
-            .name = "Internal",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_33,
-                .scl_io_num = GPIO_NUM_32,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-        //CN1 header, JST SH 1.25, GND / IO22 / IO21 / 3.3V
-        i2c::Configuration {
-            .name = "External",
-            .port = I2C_NUM_1,
-            .initMode = i2c::InitMode::Disabled,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_21,
-                .scl_io_num = GPIO_NUM_22,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        //Display
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_NC,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock()
-        },
-        //SD Card
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 8192,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr
-        }
-    },
-    .uart {
-        //CN1 header, JST SH 1.25, GND / IO22 / IO21 / 3.3V
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_21,
-            .txPin = GPIO_NUM_22,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 9600,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/cyd-jc2432w328c/Source/devices/Display.cpp

@@ -1,42 +0,0 @@
-#include "Display.h"
-
-#include <Cst816Touch.h>
-#include <PwmBacklight.h>
-#include <St7789Display.h>
-
-static std::shared_ptr<tt::hal::touch::TouchDevice> createTouch() {
-    auto configuration = std::make_unique<Cst816sTouch::Configuration>(
-        I2C_NUM_0,
-        LCD_HORIZONTAL_RESOLUTION,
-        LCD_VERTICAL_RESOLUTION
-    );
-
-    return std::make_shared<Cst816sTouch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    St7789Display::Configuration panel_configuration = {
-        .horizontalResolution = LCD_HORIZONTAL_RESOLUTION,
-        .verticalResolution = LCD_VERTICAL_RESOLUTION,
-        .gapX = 0,
-        .gapY = 0,
-        .swapXY = false,
-        .mirrorX = false,
-        .mirrorY = false,
-        .invertColor = false,
-        .bufferSize = LCD_BUFFER_SIZE,
-        .touch = createTouch(),
-        .backlightDutyFunction = driver::pwmbacklight::setBacklightDuty,
-        .resetPin = GPIO_NUM_NC
-    };
-
-    auto spi_configuration = std::make_shared<St7789Display::SpiConfiguration>(St7789Display::SpiConfiguration {
-        .spiHostDevice = LCD_SPI_HOST,
-        .csPin = LCD_PIN_CS,
-        .dcPin = LCD_PIN_DC,
-        .pixelClockFrequency = 62'500'000,
-        .transactionQueueDepth = 10
-    });
-
-    return std::make_shared<St7789Display>(panel_configuration, spi_configuration);
-}

Boards/cyd-jc2432w328c/Source/devices/Display.h

@@ -1,23 +0,0 @@
-#pragma once
-
-#include "Display.h"
-
-#include <Tactility/hal/display/DisplayDevice.h>
-#include <memory>
-#include <driver/gpio.h>
-#include <driver/spi_common.h>
-
-// Display backlight (PWM)
-constexpr auto LCD_PIN_BACKLIGHT = GPIO_NUM_27;
-
-// Display
-constexpr auto LCD_SPI_HOST = SPI2_HOST;
-constexpr auto LCD_PIN_CS = GPIO_NUM_15;
-constexpr auto LCD_PIN_DC = GPIO_NUM_2;
-constexpr auto LCD_HORIZONTAL_RESOLUTION = 240;
-constexpr auto LCD_VERTICAL_RESOLUTION = 320;
-constexpr auto LCD_BUFFER_HEIGHT = LCD_VERTICAL_RESOLUTION / 10;
-constexpr auto LCD_BUFFER_SIZE = LCD_HORIZONTAL_RESOLUTION * LCD_BUFFER_HEIGHT;
-constexpr auto LCD_SPI_TRANSFER_SIZE_LIMIT = LCD_BUFFER_SIZE * LV_COLOR_DEPTH / 8;
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/cyd-jc2432w328c/Source/devices/SdCard.cpp

@@ -1,27 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-constexpr auto SDCARD_SPI_HOST = SPI3_HOST;
-constexpr auto SDCARD_PIN_CS = GPIO_NUM_5;
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        SDCARD_PIN_CS,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        std::make_shared<tt::Mutex>(tt::Mutex::Type::Recursive),
-        std::vector<gpio_num_t>(),
-        SDCARD_SPI_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}
-

Boards/cyd-jc2432w328c/Source/devices/SdCard.h

@@ -1,8 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/sdcard/SdCardDevice.h>
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();
-

Boards/cyd-jc8048w550c/Source/Configuration.cpp

@@ -1,114 +0,0 @@
-#include "PwmBacklight.h"
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    return driver::pwmbacklight::init(GPIO_NUM_2);
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        //Touch
-        i2c::Configuration {
-            .name = "Internal",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_19,
-                .scl_io_num = GPIO_NUM_20,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-        //P4 header, JST SH 1.25, GND / 3.3V / IO17 / IO18 or
-        //P5 header, JST SH 1.0, GND / 3.3V / IO17 / IO18
-        i2c::Configuration {
-            .name = "External",
-            .port = I2C_NUM_1,
-            .initMode = i2c::InitMode::Disabled,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_17,
-                .scl_io_num = GPIO_NUM_18,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        //SD Card
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_11,
-                .miso_io_num = GPIO_NUM_13,
-                .sclk_io_num = GPIO_NUM_12,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 8192,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr
-        }
-    },
-    .uart {
-        //P4 header, JST SH 1.0, GND / 3.3V / IO17 / IO18
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_17,
-            .txPin = GPIO_NUM_18,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 9600,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/cyd-jc8048w550c/Source/devices/Display.cpp

@@ -1,105 +0,0 @@
-#include "Display.h"
-
-#include <Gt911Touch.h>
-#include <PwmBacklight.h>
-#include <RgbDisplay.h>
-#include <Tactility/Log.h>
-
-std::shared_ptr<tt::hal::touch::TouchDevice> _Nullable createTouch() {
-    // Note for future changes: Reset pin is 38 and interrupt pin is 18
-    // or INT = NC, schematic and other info floating around is kinda conflicting...
-    auto configuration = std::make_unique<Gt911Touch::Configuration>(
-        I2C_NUM_0,
-        800,
-        480
-    );
-
-    return std::make_shared<Gt911Touch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    auto touch = createTouch();
-
-    constexpr uint32_t bufferPixels = 800 * 10;
-
-    esp_lcd_rgb_panel_config_t rgb_panel_config = {
-        .clk_src = LCD_CLK_SRC_DEFAULT,
-        .timings = {
-            .pclk_hz = 16000000,
-            .h_res = 800,
-            .v_res = 480,
-            .hsync_pulse_width = 4,
-            .hsync_back_porch = 8,
-            .hsync_front_porch = 8,
-            .vsync_pulse_width = 4,
-            .vsync_back_porch = 8,
-            .vsync_front_porch = 8,
-            .flags = {
-                .hsync_idle_low = false,
-                .vsync_idle_low = false,
-                .de_idle_high = false,
-                .pclk_active_neg = true,
-                .pclk_idle_high = false
-            }
-        },
-        .data_width = 16,
-        .bits_per_pixel = 0,
-        .num_fbs = 2,
-        .bounce_buffer_size_px = bufferPixels,
-        .sram_trans_align = 8,
-        .psram_trans_align = 64,
-        .hsync_gpio_num = GPIO_NUM_39,
-        .vsync_gpio_num = GPIO_NUM_41,
-        .de_gpio_num = GPIO_NUM_40 ,
-        .pclk_gpio_num = GPIO_NUM_42,
-        .disp_gpio_num = GPIO_NUM_NC,
-        .data_gpio_nums = {
-            GPIO_NUM_8, // B3
-            GPIO_NUM_3, // B4
-            GPIO_NUM_46, // B5
-            GPIO_NUM_9, // B6
-            GPIO_NUM_1, // B7
-            GPIO_NUM_5, // G2
-            GPIO_NUM_6, // G3
-            GPIO_NUM_7, // G4
-            GPIO_NUM_15, // G5
-            GPIO_NUM_16, // G6
-            GPIO_NUM_4, // G7
-            GPIO_NUM_45, // R3
-            GPIO_NUM_48, // R4
-            GPIO_NUM_47, // R5
-            GPIO_NUM_21, // R6
-            GPIO_NUM_14, // R7
-        },
-        .flags = {
-            .disp_active_low = false,
-            .refresh_on_demand = false,
-            .fb_in_psram = true,
-            .double_fb = true,
-            .no_fb = false,
-            .bb_invalidate_cache = false
-        }
-    };
-
-    RgbDisplay::BufferConfiguration buffer_config = {
-        .size = (800 * 480),
-        .useSpi = true,
-        .doubleBuffer = true,
-        .bounceBufferMode = true,
-        .avoidTearing = false
-    };
-
-    auto configuration = std::make_unique<RgbDisplay::Configuration>(
-        rgb_panel_config,
-        buffer_config,
-        touch,
-        LV_COLOR_FORMAT_RGB565,
-        false,
-        false,
-        false,
-        false,
-        driver::pwmbacklight::setBacklightDuty
-    );
-
-    return std::make_shared<RgbDisplay>(std::move(configuration));
-}

Boards/cyd-jc8048w550c/Source/devices/SdCard.cpp

@@ -1,25 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto config = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_10,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        std::make_shared<tt::Mutex>(tt::Mutex::Type::Recursive),
-        std::vector<gpio_num_t>(),
-        SPI2_HOST
-    );
-
-    auto sdcard = std::make_shared<SpiSdCardDevice>(
-        std::move(config)
-    );
-
-    return std::static_pointer_cast<SdCardDevice>(sdcard);
-}

Boards/cyd-jc8048w550c/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/sdcard/SdCardDevice.h>
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/elecrow-crowpanel-advance-28/Source/Configuration.cpp

@@ -1,145 +0,0 @@
-#include "PwmBacklight.h"
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    return driver::pwmbacklight::init(GPIO_NUM_38);
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        // There is only 1 (internal for touch, and also serves as "I2C-OUT" port)
-        // Note: You could repurpose 1 or more UART interfaces as I2C interfaces
-        i2c::Configuration {
-            .name = "Main",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_15,
-                .scl_io_num = GPIO_NUM_16,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // Display
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_DISABLED,
-            .config = {
-                .mosi_io_num = GPIO_NUM_39,
-                .miso_io_num = GPIO_NUM_NC,
-                .sclk_io_num = GPIO_NUM_42,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-        // SD card
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_6,
-                .miso_io_num = GPIO_NUM_4,
-                .sclk_io_num = GPIO_NUM_5,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 32768,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr // No custom lock needed
-        }
-    },
-    .uart {
-        // "UART0-IN"
-        uart::Configuration {
-            .name = "UART0",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_44,
-            .txPin = GPIO_NUM_43,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        },
-        // "UART1-OUT"
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_2,
-            .rxPin = GPIO_NUM_18,
-            .txPin = GPIO_NUM_17,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/elecrow-crowpanel-advance-28/Source/devices/Display.cpp

@@ -1,46 +0,0 @@
-#include "Display.h"
-
-#include <Ft5x06Touch.h>
-#include <PwmBacklight.h>
-#include <St7789Display.h>
-
-static std::shared_ptr<tt::hal::touch::TouchDevice> createTouch() {
-    // Note for future changes: Reset pin is 48 and interrupt pin is 47
-    auto configuration = std::make_unique<Ft5x06Touch::Configuration>(
-        I2C_NUM_0,
-        LCD_HORIZONTAL_RESOLUTION,
-        LCD_VERTICAL_RESOLUTION,
-        false,
-        false,
-        false
-    );
-
-    return std::make_shared<Ft5x06Touch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    St7789Display::Configuration panel_configuration = {
-        .horizontalResolution = LCD_HORIZONTAL_RESOLUTION,
-        .verticalResolution = LCD_VERTICAL_RESOLUTION,
-        .gapX = 0,
-        .gapY = 0,
-        .swapXY = false,
-        .mirrorX = false,
-        .mirrorY = false,
-        .invertColor = true,
-        .bufferSize = LCD_BUFFER_SIZE,
-        .touch = createTouch(),
-        .backlightDutyFunction = driver::pwmbacklight::setBacklightDuty,
-        .resetPin = GPIO_NUM_NC
-    };
-
-    auto spi_configuration = std::make_shared<St7789Display::SpiConfiguration>(St7789Display::SpiConfiguration {
-        .spiHostDevice = LCD_SPI_HOST,
-        .csPin = LCD_PIN_CS,
-        .dcPin = LCD_PIN_DC,
-        .pixelClockFrequency = 62'500'000,
-        .transactionQueueDepth = 10
-    });
-
-    return std::make_shared<St7789Display>(panel_configuration, spi_configuration);
-}

Boards/elecrow-crowpanel-advance-28/Source/devices/Display.h

@@ -1,17 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/display/DisplayDevice.h>
-
-#include <driver/gpio.h>
-#include <driver/spi_common.h>
-
-constexpr auto LCD_SPI_HOST = SPI2_HOST;
-constexpr auto LCD_PIN_CS = GPIO_NUM_40;
-constexpr auto LCD_PIN_DC = GPIO_NUM_41; // RS
-constexpr auto LCD_HORIZONTAL_RESOLUTION = 240;
-constexpr auto LCD_VERTICAL_RESOLUTION = 320;
-constexpr auto LCD_BUFFER_HEIGHT = LCD_VERTICAL_RESOLUTION / 10;
-constexpr auto LCD_BUFFER_SIZE = LCD_HORIZONTAL_RESOLUTION * LCD_BUFFER_HEIGHT;
-constexpr auto LCD_SPI_TRANSFER_SIZE_LIMIT = LCD_BUFFER_SIZE * LV_COLOR_DEPTH / 8;
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/elecrow-crowpanel-advance-28/Source/devices/SdCard.cpp

@@ -1,25 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/lvgl/LvglSync.h>
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-constexpr auto CROWPANEL_SDCARD_PIN_CS = GPIO_NUM_7;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        CROWPANEL_SDCARD_PIN_CS,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        tt::lvgl::getSyncLock(),
-        std::vector<gpio_num_t>(),
-        SPI3_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/elecrow-crowpanel-advance-28/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/elecrow-crowpanel-advance-35/Source/Configuration.cpp

@@ -1,147 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <PwmBacklight.h>
-
-#define CROWPANEL_SPI_TRANSFER_SIZE_LIMIT (CROWPANEL_LCD_HORIZONTAL_RESOLUTION * CROWPANEL_LCD_SPI_TRANSFER_HEIGHT * (LV_COLOR_DEPTH / 8))
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    return driver::pwmbacklight::init(GPIO_NUM_38);
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        // There is only 1 (internal for touch, and also serves as "I2C-OUT" port)
-        // Note: You could repurpose 1 or more UART interfaces as I2C interfaces
-        i2c::Configuration {
-            .name = "Main",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_15,
-                .scl_io_num = GPIO_NUM_16,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // Display
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_DISABLED,
-            .config = {
-                .mosi_io_num = GPIO_NUM_39,
-                .miso_io_num = GPIO_NUM_NC,
-                .sclk_io_num = GPIO_NUM_42,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = CROWPANEL_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-        // SD card
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_6,
-                .miso_io_num = GPIO_NUM_4,
-                .sclk_io_num = GPIO_NUM_5,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 32768,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr // No custom lock needed
-        }
-    },
-    .uart {
-        // "UART0-IN"
-        uart::Configuration {
-            .name = "UART0",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_44,
-            .txPin = GPIO_NUM_43,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        },
-        // "UART1-OUT"
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_2,
-            .rxPin = GPIO_NUM_18,
-            .txPin = GPIO_NUM_17,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/elecrow-crowpanel-advance-35/Source/devices/Display.cpp

@@ -1,38 +0,0 @@
-#include "Display.h"
-
-#include <Gt911Touch.h>
-#include <PwmBacklight.h>
-#include <Ili9488Display.h>
-
-static std::shared_ptr<tt::hal::touch::TouchDevice> createTouch() {
-    // Note for future changes: Reset pin is 48 and interrupt pin is 47
-    auto configuration = std::make_unique<Gt911Touch::Configuration>(
-        I2C_NUM_0,
-        320,
-        480
-    );
-
-    return std::make_shared<Gt911Touch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    auto touch = createTouch();
-
-    auto configuration = std::make_unique<Ili9488Display::Configuration>(
-        CROWPANEL_LCD_SPI_HOST,
-        CROWPANEL_LCD_PIN_CS,
-        CROWPANEL_LCD_PIN_DC,
-        CROWPANEL_LCD_HORIZONTAL_RESOLUTION,
-        CROWPANEL_LCD_VERTICAL_RESOLUTION,
-        touch,
-        false,
-        false,
-        false,
-        true
-    );
-
-    configuration->backlightDutyFunction = driver::pwmbacklight::setBacklightDuty;
-
-    auto display = std::make_shared<Ili9488Display>(std::move(configuration));
-    return std::reinterpret_pointer_cast<tt::hal::display::DisplayDevice>(display);
-}

Boards/elecrow-crowpanel-advance-35/Source/devices/SdCard.cpp

@@ -1,25 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/lvgl/LvglSync.h>
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-constexpr auto CROWPANEL_SDCARD_PIN_CS = GPIO_NUM_7;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        CROWPANEL_SDCARD_PIN_CS,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        tt::lvgl::getSyncLock(),
-        std::vector<gpio_num_t>(),
-        SPI3_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/elecrow-crowpanel-advance-35/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/elecrow-crowpanel-advance-50/Source/Configuration.cpp

@@ -1,131 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <TCA9534.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    TCA9534_IO_EXP io_expander = {
-        .I2C_ADDR = 0x18,
-        .i2c_master_port = I2C_NUM_0,
-        .interrupt_pin = GPIO_NUM_NC,
-        .interrupt_task = nullptr
-    };
-
-    // Enable LCD backlight
-    set_tca9534_io_pin_direction(&io_expander, TCA9534_IO1, TCA9534_OUTPUT);
-    set_tca9534_io_pin_output_state(&io_expander, TCA9534_IO1, 255);
-
-    return true;
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        // There is only 1 (internal for touch, and also serves as "I2C-OUT" port)
-        // Note: You could repurpose 1 or more UART interfaces as I2C interfaces
-        i2c::Configuration {
-            .name = "Main",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_15,
-                .scl_io_num = GPIO_NUM_16,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // SD card
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_6,
-                .miso_io_num = GPIO_NUM_4,
-                .sclk_io_num = GPIO_NUM_5,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 8192,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr // No custom lock needed
-        }
-    },
-    .uart {
-        // "UART0-OUT"
-        uart::Configuration {
-            .name = "UART0",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_44,
-            .txPin = GPIO_NUM_43,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        },
-        // "UART1-OUT"
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_2,
-            .rxPin = GPIO_NUM_19,
-            .txPin = GPIO_NUM_20,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/elecrow-crowpanel-advance-50/Source/devices/Display.cpp

@@ -1,103 +0,0 @@
-#include "Display.h"
-
-#include <Gt911Touch.h>
-#include <RgbDisplay.h>
-#include <Tactility/Log.h>
-
-std::shared_ptr<tt::hal::touch::TouchDevice> _Nullable createTouch() {
-    // Note for future changes: Reset pin is 38 and interrupt pin is 18
-    // or INT = NC, schematic and other info floating around is kinda conflicting...
-    auto configuration = std::make_unique<Gt911Touch::Configuration>(
-        I2C_NUM_0,
-        800,
-        480
-    );
-
-    return std::make_shared<Gt911Touch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    auto touch = createTouch();
-
-    constexpr uint32_t bufferPixels = 800 * 10;
-
-    esp_lcd_rgb_panel_config_t rgb_panel_config = {
-        .clk_src = LCD_CLK_SRC_DEFAULT,
-        .timings = {
-            .pclk_hz = 15000000, // TODO: 21 MHz was too much and caused drift when opening wifi/SD/apps. Try something inbetween 15 and 21 MHz.
-            .h_res = 800,
-            .v_res = 480,
-            .hsync_pulse_width = 4,
-            .hsync_back_porch = 8,
-            .hsync_front_porch = 8,
-            .vsync_pulse_width = 4,
-            .vsync_back_porch = 8,
-            .vsync_front_porch = 8,
-            .flags = {
-                .hsync_idle_low = false,
-                .vsync_idle_low = false,
-                .de_idle_high = false,
-                .pclk_active_neg = true,
-                .pclk_idle_high = false
-            }
-        },
-        .data_width = 16,
-        .bits_per_pixel = 0,
-        .num_fbs = 2,
-        .bounce_buffer_size_px = bufferPixels,
-        .sram_trans_align = 8,
-        .psram_trans_align = 64,
-        .hsync_gpio_num = GPIO_NUM_40,
-        .vsync_gpio_num = GPIO_NUM_41,
-        .de_gpio_num = GPIO_NUM_42 ,
-        .pclk_gpio_num = GPIO_NUM_39,
-        .disp_gpio_num = GPIO_NUM_NC,
-        .data_gpio_nums = {
-            GPIO_NUM_21, // B3
-            GPIO_NUM_47, // B4
-            GPIO_NUM_48, // B5
-            GPIO_NUM_45, // B6
-            GPIO_NUM_38, // B7
-            GPIO_NUM_9, // G2
-            GPIO_NUM_10, // G3
-            GPIO_NUM_11, // G4
-            GPIO_NUM_12, // G5
-            GPIO_NUM_13, // G6
-            GPIO_NUM_14, // G7
-            GPIO_NUM_7, // R3
-            GPIO_NUM_17, // R4
-            GPIO_NUM_18, // R5
-            GPIO_NUM_3, // R6
-            GPIO_NUM_46, // R7
-        },
-        .flags = {
-            .disp_active_low = false,
-            .refresh_on_demand = false,
-            .fb_in_psram = true,
-            .double_fb = true,
-            .no_fb = false,
-            .bb_invalidate_cache = false
-        }
-    };
-
-    RgbDisplay::BufferConfiguration buffer_config = {
-        .size = (800 * 480),
-        .useSpi = true,
-        .doubleBuffer = true,
-        .bounceBufferMode = true,
-        .avoidTearing = false
-    };
-
-    auto configuration = std::make_unique<RgbDisplay::Configuration>(
-        rgb_panel_config,
-        buffer_config,
-        touch,
-        LV_COLOR_FORMAT_RGB565,
-        false,
-        false,
-        false,
-        false
-    );
-
-    return std::make_shared<RgbDisplay>(std::move(configuration));
-}

Boards/elecrow-crowpanel-advance-50/Source/devices/SdCard.cpp

@@ -1,21 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        // See https://github.com/Elecrow-RD/CrowPanel-Advance-HMI-ESP32-AI-Display/blob/master/5.0/factory_code/factory_code.ino
-        GPIO_NUM_0, // It's actually not connected, but in the demo pin 0 is used
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/elecrow-crowpanel-advance-50/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/sdcard/SdCardDevice.h>
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/elecrow-crowpanel-basic-28/Source/Configuration.cpp

@@ -1,123 +0,0 @@
-#include "PwmBacklight.h"
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <Xpt2046Power.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    return driver::pwmbacklight::init(GPIO_NUM_27);
-}
-
-static DeviceVector createDevices() {
-    return {
-        std::make_shared<Xpt2046Power>(),
-        createDisplay(),
-        createSdCard(),
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        // There is only 1 (internal for touch, and also serves as "I2C-OUT" port)
-        // Note: You could repurpose 1 or more UART interfaces as I2C interfaces
-        i2c::Configuration {
-            .name = "Main",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_22,
-                .scl_io_num = GPIO_NUM_21,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // Display
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_DISABLED,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_12,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-        // SD card
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 32768,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr // No custom lock needed
-        }
-    },
-    .uart {
-        // "UART1"
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_16,
-            .txPin = GPIO_NUM_17,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/elecrow-crowpanel-basic-28/Source/devices/SdCard.cpp

@@ -1,23 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/lvgl/LvglSync.h>
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_5,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        tt::lvgl::getSyncLock(),
-        std::vector<gpio_num_t>(),
-        SPI3_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/elecrow-crowpanel-basic-28/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/elecrow-crowpanel-basic-35/Source/Configuration.cpp

@@ -1,125 +0,0 @@
-#include "PwmBacklight.h"
-#include "Tactility/lvgl/LvglSync.h"
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Xpt2046Power.h>
-
-constexpr auto CROWPANEL_SPI_TRANSFER_SIZE_LIMIT = (CROWPANEL_LCD_HORIZONTAL_RESOLUTION * CROWPANEL_LCD_SPI_TRANSFER_HEIGHT * (LV_COLOR_DEPTH / 8));
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    return driver::pwmbacklight::init(GPIO_NUM_27);
-}
-
-static DeviceVector createDevices() {
-    return {
-        std::make_shared<Xpt2046Power>(),
-        createDisplay(),
-        createSdCard(),
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        // There is only 1 (internal for touch, and also serves as "I2C-OUT" port)
-        // Note: You could repurpose 1 or more UART interfaces as I2C interfaces
-        i2c::Configuration {
-            .name = "Main",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_22,
-                .scl_io_num = GPIO_NUM_21,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // Display
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_DISABLED,
-            .config = {
-                .mosi_io_num = GPIO_NUM_13,
-                .miso_io_num = GPIO_NUM_33,
-                .sclk_io_num = GPIO_NUM_14,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = CROWPANEL_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-        // SD card
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_23,
-                .miso_io_num = GPIO_NUM_19,
-                .sclk_io_num = GPIO_NUM_18,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 32768,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr // No custom lock needed
-        }
-    },
-    .uart {
-        // "UART1"
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_3,
-            .txPin = GPIO_NUM_1,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/elecrow-crowpanel-basic-35/Source/devices/SdCard.cpp

@@ -1,23 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/lvgl/LvglSync.h>
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_5,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        tt::lvgl::getSyncLock(),
-        std::vector<gpio_num_t>(),
-        SPI3_HOST
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/elecrow-crowpanel-basic-35/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/elecrow-crowpanel-basic-50/Source/Configuration.cpp

@@ -1,97 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <PwmBacklight.h>
-
-using namespace tt::hal;
-
-static bool initBoot() {
-    // Note: I tried 100 Hz to 100 kHz and couldn't get the flickering to stop
-    return driver::pwmbacklight::init(GPIO_NUM_2);
-}
-
-static DeviceVector createDevices() {
-    return {
-        createDisplay(),
-        createSdCard(),
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        // There is only 1 (internal for touch, and also serves as "I2C-OUT" port)
-        // Note: You could repurpose 1 or more UART interfaces as I2C interfaces
-        i2c::Configuration {
-            .name = "Main",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_19,
-                .scl_io_num = GPIO_NUM_20,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        // SD card
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_11,
-                .miso_io_num = GPIO_NUM_13,
-                .sclk_io_num = GPIO_NUM_12,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 8192,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr
-        }
-    },
-    .uart {
-        // "UART1"
-        uart::Configuration {
-            .name = "UART1",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_44,
-            .txPin = GPIO_NUM_43,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/elecrow-crowpanel-basic-50/Source/devices/Display.cpp

@@ -1,106 +0,0 @@
-#include "Display.h"
-
-#include <Gt911Touch.h>
-#include <PwmBacklight.h>
-#include <RgbDisplay.h>
-#include <Tactility/Log.h>
-
-std::shared_ptr<tt::hal::touch::TouchDevice> _Nullable createTouch() {
-    // Note for future changes: Reset pin is 38 and interrupt pin is 18
-    // or INT = NC, schematic and other info floating around is kinda conflicting...
-    auto configuration = std::make_unique<Gt911Touch::Configuration>(
-        I2C_NUM_0,
-        800,
-        480
-    );
-
-    return std::make_shared<Gt911Touch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    auto touch = createTouch();
-
-    constexpr uint32_t bufferPixels = 800 * 10;
-
-    esp_lcd_rgb_panel_config_t rgb_panel_config = {
-        .clk_src = LCD_CLK_SRC_DEFAULT,
-        .timings = {
-            .pclk_hz = 15000000,
-            .h_res = 800,
-            .v_res = 480,
-            .hsync_pulse_width = 4,
-            .hsync_back_porch = 43,
-            .hsync_front_porch = 8,
-            .vsync_pulse_width = 4,
-            .vsync_back_porch = 12,
-            .vsync_front_porch = 8,
-            .flags = {
-                .hsync_idle_low = false,
-                .vsync_idle_low = false,
-                .de_idle_high = false,
-                .pclk_active_neg = true,
-                .pclk_idle_high = false
-            }
-        },
-        .data_width = 16,
-        .bits_per_pixel = 0,
-        .num_fbs = 2,
-        .bounce_buffer_size_px = bufferPixels,
-        .sram_trans_align = 8,
-        .psram_trans_align = 64,
-        .hsync_gpio_num = GPIO_NUM_39,
-        .vsync_gpio_num = GPIO_NUM_41,
-        .de_gpio_num = GPIO_NUM_40 ,
-        .pclk_gpio_num = GPIO_NUM_0,
-        .disp_gpio_num = GPIO_NUM_NC,
-        .data_gpio_nums = {
-            GPIO_NUM_8, // B0
-            GPIO_NUM_3, // B1
-            GPIO_NUM_46, // B2
-            GPIO_NUM_9, // B3
-            GPIO_NUM_1, // B4
-            GPIO_NUM_5, // G0
-            GPIO_NUM_6, // G1
-            GPIO_NUM_7, // G2
-            GPIO_NUM_15, // G3
-            GPIO_NUM_16, // G4
-            GPIO_NUM_4, // G5
-            GPIO_NUM_45, // R0
-            GPIO_NUM_48, // R1
-            GPIO_NUM_47, // R2
-            GPIO_NUM_21, // R3
-            GPIO_NUM_14, // R4
-        },
-        .flags = {
-            .disp_active_low = false,
-            .refresh_on_demand = false,
-            .fb_in_psram = true,
-            .double_fb = true,
-            .no_fb = false,
-            .bb_invalidate_cache = false
-        }
-    };
-
-    RgbDisplay::BufferConfiguration buffer_config = {
-        .size = (800 * 480),
-        .useSpi = true,
-        .doubleBuffer = true,
-        .bounceBufferMode = true,
-        .avoidTearing = false
-    };
-
-    auto configuration = std::make_unique<RgbDisplay::Configuration>(
-        rgb_panel_config,
-        buffer_config,
-        touch,
-        LV_COLOR_FORMAT_RGB565,
-        false,
-        false,
-        false,
-        false,
-        driver::pwmbacklight::setBacklightDuty
-    );
-
-    auto display = std::make_shared<RgbDisplay>(std::move(configuration));
-    return std::reinterpret_pointer_cast<tt::hal::display::DisplayDevice>(display);
-}

Boards/elecrow-crowpanel-basic-50/Source/devices/SdCard.cpp

@@ -1,19 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        GPIO_NUM_10,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/elecrow-crowpanel-basic-50/Source/devices/SdCard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/sdcard/SdCardDevice.h>
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/lilygo-tdeck/Source/Configuration.cpp

@@ -1,111 +0,0 @@
-#include "devices/Display.h"
-#include "devices/Power.h"
-#include "devices/Sdcard.h"
-#include "devices/TdeckKeyboard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-bool initBoot();
-
-using namespace tt::hal;
-
-static std::vector<std::shared_ptr<Device>> createDevices() {
-    return {
-        createPower(),
-        createDisplay(),
-        std::make_shared<TdeckKeyboard>(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .createDevices = createDevices,
-    .i2c = {
-        i2c::Configuration {
-            .name = "Internal",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_18,
-                .scl_io_num = GPIO_NUM_8,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-        i2c::Configuration {
-            .name = "External",
-            .port = I2C_NUM_1,
-            .initMode = i2c::InitMode::Disabled,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_43,
-                .scl_io_num = GPIO_NUM_44,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_41,
-                .miso_io_num = GPIO_NUM_38,
-                .sclk_io_num = GPIO_NUM_40,
-                .quadwp_io_num = GPIO_NUM_NC, // Quad SPI LCD driver is not yet supported
-                .quadhd_io_num = GPIO_NUM_NC, // Quad SPI LCD driver is not yet supported
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        }
-    },
-    .uart {
-        uart::Configuration {
-            .name = "Grove",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_44,
-            .txPin = GPIO_NUM_43,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 38400,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/lilygo-tdeck/Source/Init.cpp

@@ -1,63 +0,0 @@
-#include "PwmBacklight.h"
-#include "Tactility/kernel/SystemEvents.h"
-#include "Tactility/service/gps/GpsService.h"
-
-#include <Tactility/TactilityCore.h>
-#include <Tactility/hal/gps/GpsConfiguration.h>
-
-#define TAG "tdeck"
-
-// Power on
-#define TDECK_POWERON_GPIO GPIO_NUM_10
-
-static bool powerOn() {
-    gpio_config_t device_power_signal_config = {
-        .pin_bit_mask = BIT64(TDECK_POWERON_GPIO),
-        .mode = GPIO_MODE_OUTPUT,
-        .pull_up_en = GPIO_PULLUP_DISABLE,
-        .pull_down_en = GPIO_PULLDOWN_DISABLE,
-        .intr_type = GPIO_INTR_DISABLE,
-    };
-
-    if (gpio_config(&device_power_signal_config) != ESP_OK) {
-        return false;
-    }
-
-    if (gpio_set_level(TDECK_POWERON_GPIO, 1) != ESP_OK) {
-        return false;
-    }
-
-    return true;
-}
-
-bool initBoot() {
-    ESP_LOGI(TAG, LOG_MESSAGE_POWER_ON_START);
-    if (!powerOn()) {
-        TT_LOG_E(TAG, LOG_MESSAGE_POWER_ON_FAILED);
-        return false;
-    }
-
-    /* 32 Khz and higher gives an issue where the screen starts dimming again above 80% brightness
-     * when moving the brightness slider rapidly from a lower setting to 100%.
-     * This is not a slider bug (data was debug-traced) */
-    if (!driver::pwmbacklight::init(GPIO_NUM_42, 30000)) {
-        TT_LOG_E(TAG, "Backlight init failed");
-        return false;
-    }
-
-    tt::kernel::subscribeSystemEvent(tt::kernel::SystemEvent::BootSplash, [](tt::kernel::SystemEvent event) {
-        auto gps_service = tt::service::gps::findGpsService();
-        if (gps_service != nullptr) {
-            std::vector<tt::hal::gps::GpsConfiguration> gps_configurations;
-            gps_service->getGpsConfigurations(gps_configurations);
-            if (gps_configurations.empty()) {
-                if (gps_service->addGpsConfiguration(tt::hal::gps::GpsConfiguration {.uartName = "Grove", .baudRate = 38400, .model = tt::hal::gps::GpsModel::UBLOX10})) {
-                    TT_LOG_I(TAG, "Configured internal GPS");
-                } else {
-                    TT_LOG_E(TAG, "Failed to configure internal GPS");
-                }
-            }
-        }
-    });
-    return true;
-}

Boards/lilygo-tdeck/Source/devices/Display.cpp

@@ -1,46 +0,0 @@
-#include "Display.h"
-
-#include <Gt911Touch.h>
-#include <PwmBacklight.h>
-#include <St7789Display.h>
-
-static std::shared_ptr<tt::hal::touch::TouchDevice> createTouch() {
-    // Note for future changes: Reset pin is 48 and interrupt pin is 47
-    auto configuration = std::make_unique<Gt911Touch::Configuration>(
-        I2C_NUM_0,
-        240,
-        320,
-        true,
-        true,
-        false
-    );
-
-    return std::make_shared<Gt911Touch>(std::move(configuration));
-}
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    St7789Display::Configuration panel_configuration = {
-        .horizontalResolution = 320,
-        .verticalResolution = 240,
-        .gapX = 0,
-        .gapY = 0,
-        .swapXY = true,
-        .mirrorX = true,
-        .mirrorY = false,
-        .invertColor = true,
-        .bufferSize = LCD_BUFFER_SIZE,
-        .touch = createTouch(),
-        .backlightDutyFunction = driver::pwmbacklight::setBacklightDuty,
-        .resetPin = GPIO_NUM_NC
-    };
-
-    auto spi_configuration = std::make_shared<St7789Display::SpiConfiguration>(St7789Display::SpiConfiguration {
-        .spiHostDevice = LCD_SPI_HOST,
-        .csPin = LCD_PIN_CS,
-        .dcPin = LCD_PIN_DC,
-        .pixelClockFrequency = 62'500'000,
-        .transactionQueueDepth = 10
-    });
-
-    return std::make_shared<St7789Display>(panel_configuration, spi_configuration);
-}

Boards/lilygo-tdeck/Source/devices/Display.h

@@ -1,16 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/display/DisplayDevice.h>
-#include <driver/gpio.h>
-#include <driver/spi_common.h>
-
-constexpr auto LCD_SPI_HOST = SPI2_HOST;
-constexpr auto LCD_PIN_CS = GPIO_NUM_12;
-constexpr auto LCD_PIN_DC = GPIO_NUM_11; // RS
-constexpr auto LCD_HORIZONTAL_RESOLUTION = 320;
-constexpr auto LCD_VERTICAL_RESOLUTION = 240;
-constexpr auto LCD_BUFFER_HEIGHT = (LCD_VERTICAL_RESOLUTION / 3);
-constexpr auto LCD_BUFFER_SIZE = (LCD_HORIZONTAL_RESOLUTION * LCD_BUFFER_HEIGHT);
-constexpr auto LCD_SPI_TRANSFER_SIZE_LIMIT = LCD_BUFFER_SIZE * LV_COLOR_DEPTH / 8;
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay();

Boards/lilygo-tdeck/Source/devices/Sdcard.cpp

@@ -1,29 +0,0 @@
-#include "Sdcard.h"
-
-#include <Tactility/lvgl/LvglSync.h>
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-constexpr auto TDECK_SDCARD_PIN_CS = GPIO_NUM_39;
-constexpr auto TDECK_LCD_PIN_CS = GPIO_NUM_12;
-constexpr auto TDECK_RADIO_PIN_CS = GPIO_NUM_9;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        TDECK_SDCARD_PIN_CS,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        tt::lvgl::getSyncLock(),
-        std::vector {
-            TDECK_RADIO_PIN_CS,
-            TDECK_LCD_PIN_CS
-        }
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/lilygo-tdeck/Source/devices/Sdcard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/lilygo-tdeck/Source/devices/TdeckKeyboard.cpp

@@ -1,62 +0,0 @@
-#include "TdeckKeyboard.h"
-#include <Tactility/hal/i2c/I2c.h>
-#include <driver/i2c.h>
-
-constexpr auto* TAG = "TdeckKeyboard";
-constexpr auto TDECK_KEYBOARD_I2C_BUS_HANDLE = I2C_NUM_0;
-constexpr auto TDECK_KEYBOARD_SLAVE_ADDRESS = 0x55;
-
-static bool keyboard_i2c_read(uint8_t* output) {
-    return tt::hal::i2c::masterRead(TDECK_KEYBOARD_I2C_BUS_HANDLE, TDECK_KEYBOARD_SLAVE_ADDRESS, output, 1, 100 / portTICK_PERIOD_MS);
-}
-
-/**
- * The callback simulates press and release events, because the T-Deck
- * keyboard only publishes press events on I2C.
- * LVGL currently works without those extra release events, but they
- * are implemented for correctness and future compatibility.
- *
- * @param indev_drv
- * @param data
- */
-static void keyboard_read_callback(TT_UNUSED lv_indev_t* indev, lv_indev_data_t* data) {
-    static uint8_t last_buffer = 0x00;
-    uint8_t read_buffer = 0x00;
-
-    // Defaults
-    data->key = 0;
-    data->state = LV_INDEV_STATE_RELEASED;
-
-    if (keyboard_i2c_read(&read_buffer)) {
-        if (read_buffer == 0 && read_buffer != last_buffer) {
-            TT_LOG_D(TAG, "Released %d", last_buffer);
-            data->key = last_buffer;
-            data->state = LV_INDEV_STATE_RELEASED;
-        } else if (read_buffer != 0) {
-            TT_LOG_D(TAG, "Pressed %d", read_buffer);
-            data->key = read_buffer;
-            data->state = LV_INDEV_STATE_PRESSED;
-        }
-    }
-
-    last_buffer = read_buffer;
-}
-
-bool TdeckKeyboard::startLvgl(lv_display_t* display) {
-    deviceHandle = lv_indev_create();
-    lv_indev_set_type(deviceHandle, LV_INDEV_TYPE_KEYPAD);
-    lv_indev_set_read_cb(deviceHandle, &keyboard_read_callback);
-    lv_indev_set_display(deviceHandle, display);
-    lv_indev_set_user_data(deviceHandle, this);
-    return true;
-}
-
-bool TdeckKeyboard::stopLvgl() {
-    lv_indev_delete(deviceHandle);
-    deviceHandle = nullptr;
-    return true;
-}
-
-bool TdeckKeyboard::isAttached() const {
-    return tt::hal::i2c::masterHasDeviceAtAddress(TDECK_KEYBOARD_I2C_BUS_HANDLE, TDECK_KEYBOARD_SLAVE_ADDRESS, 100);
-}

Boards/lilygo-tdeck/Source/devices/TdeckKeyboard.h

@@ -1,19 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/keyboard/KeyboardDevice.h>
-#include <Tactility/TactilityCore.h>
-
-class TdeckKeyboard final : public tt::hal::keyboard::KeyboardDevice {
-
-    lv_indev_t* _Nullable deviceHandle = nullptr;
-
-public:
-
-    std::string getName() const override { return "T-Deck Keyboard"; }
-    std::string getDescription() const override { return "I2C keyboard"; }
-
-    bool startLvgl(lv_display_t* display) override;
-    bool stopLvgl() override;
-    bool isAttached() const override;
-    lv_indev_t* _Nullable getLvglIndev() override { return deviceHandle; }
-};

Boards/lilygo-tdongle-s3/Source/Configuration.cpp

@@ -1,92 +0,0 @@
-#include "devices/Display.h"
-#include "devices/Sdcard.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-#define TDECK_SPI_TRANSFER_SIZE_LIMIT (80 * 160 * (LV_COLOR_DEPTH / 8))
-
-bool initBoot();
-
-using namespace tt::hal;
-
-static std::vector<std::shared_ptr<Device>> createDevices() {
-    return {
-        createDisplay(),
-        createSdCard()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .uiScale = UiScale::Smallest,
-    .createDevices = createDevices,
-    .i2c = {
-        i2c::Configuration {
-            .name = "STEMMA QT",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_44,
-                .scl_io_num = GPIO_NUM_43,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_3,
-                .miso_io_num = GPIO_NUM_NC,
-                .sclk_io_num = GPIO_NUM_5,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = TDECK_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-        },
-    },
-    .uart {
-        uart::Configuration {
-            .name = "STEMMA QT",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_44,
-            .txPin = GPIO_NUM_43,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 38400,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};

Boards/lilygo-tdongle-s3/Source/Init.cpp

@@ -1,15 +0,0 @@
-#include "PwmBacklight.h"
-#include "Tactility/service/gps/GpsService.h"
-
-#include <Tactility/TactilityCore.h>
-
-#define TAG "T-Dongle"
-
-bool initBoot() {
-    if (!driver::pwmbacklight::init(GPIO_NUM_38, 12000)) {
-        TT_LOG_E(TAG, "Backlight init failed");
-        return false;
-    }
-
-    return true;
-}

Boards/lilygo-tdongle-s3/Source/devices/Display.cpp

@@ -1,36 +0,0 @@
-#include "Display.h"
-
-#include <PwmBacklight.h>
-#include <St7735Display.h>
-
-#define LCD_SPI_HOST SPI3_HOST
-#define LCD_PIN_CS GPIO_NUM_4
-#define LCD_PIN_DC GPIO_NUM_2
-#define LCD_PIN_RESET GPIO_NUM_1
-#define LCD_HORIZONTAL_RESOLUTION 80
-#define LCD_VERTICAL_RESOLUTION 160
-#define LCD_SPI_TRANSFER_HEIGHT LCD_VERTICAL_RESOLUTION / 4
-
-std::shared_ptr<tt::hal::display::DisplayDevice> createDisplay() {
-    auto configuration = std::make_unique<St7735Display::Configuration>(
-        LCD_SPI_HOST,
-        LCD_PIN_CS,
-        LCD_PIN_DC,
-        LCD_PIN_RESET,
-        80,
-        160,
-        nullptr,
-        false,
-        false,
-        false,
-        true,
-        0,
-        26,
-        1
-    );
-
-    configuration->backlightDutyFunction = driver::pwmbacklight::setBacklightDuty;
-
-    auto display = std::make_shared<St7735Display>(std::move(configuration));
-    return std::reinterpret_pointer_cast<tt::hal::display::DisplayDevice>(display);
-}

Boards/lilygo-tdongle-s3/Source/devices/Sdcard.cpp

@@ -1,22 +0,0 @@
-#include "Sdcard.h"
-
-#include <Tactility/hal/sdcard/SdmmcDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using tt::hal::sdcard::SdmmcDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard() {
-    auto configuration = std::make_unique<SdmmcDevice::Config>(
-        GPIO_NUM_12,
-        GPIO_NUM_16,
-        GPIO_NUM_14,
-        GPIO_NUM_17,
-        GPIO_NUM_21,
-        GPIO_NUM_18,
-        SdCardDevice::MountBehaviour::AtBoot
-    );
-
-    return std::make_shared<SdmmcDevice>(
-        std::move(configuration)
-    );
-}

Boards/lilygo-tdongle-s3/Source/devices/Sdcard.h

@@ -1,7 +0,0 @@
-#pragma once
-
-#include "Tactility/hal/sdcard/SdCardDevice.h"
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createSdCard();

Boards/lilygo-tlora-pager/CMakeLists.txt

@@ -1,7 +0,0 @@
-file(GLOB_RECURSE SOURCE_FILES Source/*.c*)
-
-idf_component_register(
-    SRCS ${SOURCE_FILES}
-    INCLUDE_DIRS "Source"
-    REQUIRES Tactility esp_lcd ST7796 BQ25896 BQ27220 TCA8418 DRV2605 PwmBacklight driver esp_adc
-)

Boards/lilygo-tlora-pager/Source/Configuration.cpp

@@ -1,106 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-#include "devices/TpagerEncoder.h"
-#include "devices/TpagerKeyboard.h"
-#include "devices/TpagerPower.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-#include <Bq25896.h>
-#include <Drv2605.h>
-
-#define TPAGER_SPI_TRANSFER_SIZE_LIMIT (480 * 222 * (LV_COLOR_DEPTH / 8))
-
-bool tpagerInit();
-
-using namespace tt::hal;
-
-static DeviceVector createDevices() {
-    auto bq27220 = std::make_shared<Bq27220>(I2C_NUM_0);
-    auto power = std::make_shared<TpagerPower>(bq27220);
-
-    auto tca8418 = std::make_shared<Tca8418>(I2C_NUM_0);
-    auto keyboard = std::make_shared<TpagerKeyboard>(tca8418);
-
-    return std::vector<std::shared_ptr<Device>> {
-        tca8418,
-        std::make_shared<Bq25896>(I2C_NUM_0),
-        bq27220,
-        std::make_shared<Drv2605>(I2C_NUM_0),
-        power,
-        createTpagerSdCard(),
-        createDisplay(),
-        keyboard,
-        std::make_shared<TpagerEncoder>()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = tpagerInit,
-    .createDevices = createDevices,
-    .i2c = {
-        i2c::Configuration {
-            .name = "Internal",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_3,
-                .scl_io_num = GPIO_NUM_2,
-                .sda_pullup_en = false,
-                .scl_pullup_en = false,
-                .master = {
-                    .clk_speed = 100'000
-                },
-                .clk_flags = 0
-            }
-        }
-    },
-    .spi {spi::Configuration {
-        .device = SPI2_HOST,
-        .dma = SPI_DMA_CH_AUTO,
-        .config = {
-            .mosi_io_num = GPIO_NUM_34,
-            .miso_io_num = GPIO_NUM_33,
-            .sclk_io_num = GPIO_NUM_35,
-            .quadwp_io_num = GPIO_NUM_NC, // Quad SPI LCD driver is not yet supported
-            .quadhd_io_num = GPIO_NUM_NC, // Quad SPI LCD driver is not yet supported
-            .data4_io_num = GPIO_NUM_NC,
-            .data5_io_num = GPIO_NUM_NC,
-            .data6_io_num = GPIO_NUM_NC,
-            .data7_io_num = GPIO_NUM_NC,
-            .data_io_default_level = false,
-            .max_transfer_sz = TPAGER_SPI_TRANSFER_SIZE_LIMIT,
-            .flags = 0,
-            .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-            .intr_flags = 0
-        },
-        .initMode = spi::InitMode::ByTactility,
-        .isMutable = false,
-        .lock = tt::lvgl::getSyncLock() // esp_lvgl_port owns the lock for the display
-    }},
-    .uart {uart::Configuration {
-        .name = "Internal",
-        .port = UART_NUM_1,
-        .rxPin = GPIO_NUM_4,
-        .txPin = GPIO_NUM_12,
-        .rtsPin = GPIO_NUM_NC,
-        .ctsPin = GPIO_NUM_NC,
-        .rxBufferSize = 1024,
-        .txBufferSize = 1024,
-        .config = {
-            .baud_rate = 38400,
-            .data_bits = UART_DATA_8_BITS,
-            .parity = UART_PARITY_DISABLE,
-            .stop_bits = UART_STOP_BITS_1,
-            .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-            .rx_flow_ctrl_thresh = 0,
-            .source_clk = UART_SCLK_DEFAULT,
-            .flags = {
-                .allow_pd = 0,
-                .backup_before_sleep = 0,
-            }
-        }
-    }}
-};

Boards/lilygo-tlora-pager/Source/Init.cpp

@@ -1,56 +0,0 @@
-#include <Bq27220.h>
-#include <Tactility/TactilityCore.h>
-#include <Tactility/kernel/SystemEvents.h>
-#include <Tactility/service/gps/GpsService.h>
-#include <Tactility/hal/gps/GpsConfiguration.h>
-
-#include <driver/gpio.h>
-
-#include <PwmBacklight.h>
-
-constexpr auto* TAG = "TLoraPager";
-
-bool tpagerInit() {
-    ESP_LOGI(TAG, LOG_MESSAGE_POWER_ON_START);
-
-    /* 32 Khz and higher gives an issue where the screen starts dimming again above 80% brightness
-     * when moving the brightness slider rapidly from a lower setting to 100%.
-     * This is not a slider bug (data was debug-traced) */
-    if (!driver::pwmbacklight::init(GPIO_NUM_42, 30000)) {
-        TT_LOG_E(TAG, "Backlight init failed");
-        return false;
-    }
-
-    tt::kernel::subscribeSystemEvent(tt::kernel::SystemEvent::BootSplash, [](auto) {
-        tt::hal::findDevices([](auto device) {
-            if (device->getName() == "BQ27220") {
-                auto bq27220 = std::reinterpret_pointer_cast<Bq27220>(device);
-                if (bq27220 != nullptr) {
-                    bq27220->configureCapacity(1500, 1500);
-                    return false;
-                }
-            }
-
-            return true;
-        });
-
-        auto gps_service = tt::service::gps::findGpsService();
-        if (gps_service != nullptr) {
-            std::vector<tt::hal::gps::GpsConfiguration> gps_configurations;
-            gps_service->getGpsConfigurations(gps_configurations);
-            if (gps_configurations.empty()) {
-                if (gps_service->addGpsConfiguration(tt::hal::gps::GpsConfiguration {
-                    .uartName = "Internal",
-                    .baudRate = 38400,
-                    .model = tt::hal::gps::GpsModel::UBLOX10
-                })) {
-                    TT_LOG_I(TAG, "Configured internal GPS");
-                } else {
-                    TT_LOG_E(TAG, "Failed to configure internal GPS");
-                }
-            }
-        }
-    });
-
-    return true;
-}

Boards/lilygo-tlora-pager/Source/devices/SdCard.cpp

@@ -1,29 +0,0 @@
-#include "SdCard.h"
-
-#include <Tactility/hal/sdcard/SpiSdCardDevice.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-using tt::hal::sdcard::SpiSdCardDevice;
-
-constexpr auto TPAGER_SDCARD_PIN_CS = GPIO_NUM_21;
-constexpr auto TPAGER_LCD_PIN_CS = GPIO_NUM_38;
-constexpr auto TPAGER_RADIO_PIN_CS = GPIO_NUM_36;
-
-std::shared_ptr<SdCardDevice> createTpagerSdCard() {
-    auto configuration = std::make_unique<SpiSdCardDevice::Config>(
-        TPAGER_SDCARD_PIN_CS,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        GPIO_NUM_NC,
-        SdCardDevice::MountBehaviour::AtBoot,
-        tt::lvgl::getSyncLock(),
-        std::vector {
-            TPAGER_RADIO_PIN_CS,
-            TPAGER_LCD_PIN_CS
-        }
-    );
-
-    return std::make_shared<SpiSdCardDevice>(
-        std::move(configuration)
-    );
-}

Boards/lilygo-tlora-pager/Source/devices/SdCard.h

@@ -1,8 +0,0 @@
-#pragma once
-
-#include <Tactility/hal/sdcard/SdCardDevice.h>
-#include <memory>
-
-using tt::hal::sdcard::SdCardDevice;
-
-std::shared_ptr<SdCardDevice> createTpagerSdCard();

Boards/lilygo-tlora-pager/Source/devices/TpagerEncoder.cpp

@@ -1,141 +0,0 @@
-#include "TpagerEncoder.h"
-
-#include <Tactility/Log.h>
-#include <driver/gpio.h>
-
-constexpr auto* TAG = "TpagerEncoder";
-constexpr auto ENCODER_A = GPIO_NUM_40;
-constexpr auto ENCODER_B = GPIO_NUM_41;
-constexpr auto ENCODER_ENTER = GPIO_NUM_7;
-
-void TpagerEncoder::readCallback(lv_indev_t* indev, lv_indev_data_t* data) {
-    TpagerEncoder* encoder = static_cast<TpagerEncoder*>(lv_indev_get_user_data(indev));
-    constexpr int enter_filter_threshold = 2;
-    static int enter_filter = 0;
-    constexpr int pulses_click = 4;
-    static int pulses_prev = 0;
-
-    // Defaults
-    data->enc_diff = 0;
-    data->state = LV_INDEV_STATE_RELEASED;
-
-    int pulses = encoder->getEncoderPulses();
-    int pulse_diff = (pulses - pulses_prev);
-    if ((pulse_diff > pulses_click) || (pulse_diff < -pulses_click)) {
-        data->enc_diff = pulse_diff / pulses_click;
-        pulses_prev = pulses;
-    }
-
-    bool enter = !gpio_get_level(ENCODER_ENTER);
-    if (enter && (enter_filter < enter_filter_threshold)) {
-        enter_filter++;
-    }
-    if (!enter && (enter_filter > 0)) {
-        enter_filter--;
-    }
-
-    if (enter_filter == enter_filter_threshold) {
-        data->state = LV_INDEV_STATE_PRESSED;
-    }
-}
-
-void TpagerEncoder::initEncoder() {
-    constexpr int LOW_LIMIT = -127;
-    constexpr int HIGH_LIMIT = 126;
-
-    // Accum. count makes it that over- and underflows are automatically compensated.
-    // Prerequisite: watchpoints at low and high limit
-    pcnt_unit_config_t unit_config = {
-        .low_limit = LOW_LIMIT,
-        .high_limit = HIGH_LIMIT,
-        .flags = {.accum_count = 1},
-    };
-
-    if (pcnt_new_unit(&unit_config, &encPcntUnit) != ESP_OK) {
-        TT_LOG_E(TAG, "Pulsecounter intialization failed");
-    }
-
-    pcnt_glitch_filter_config_t filter_config = {
-        .max_glitch_ns = 1000,
-    };
-
-    if (pcnt_unit_set_glitch_filter(encPcntUnit, &filter_config) != ESP_OK) {
-        TT_LOG_E(TAG, "Pulsecounter glitch filter config failed");
-    }
-
-    pcnt_chan_config_t chan_1_config = {
-        .edge_gpio_num = ENCODER_B,
-        .level_gpio_num = ENCODER_A,
-    };
-
-    pcnt_chan_config_t chan_2_config = {
-        .edge_gpio_num = ENCODER_A,
-        .level_gpio_num = ENCODER_B,
-    };
-
-    pcnt_channel_handle_t pcnt_chan_1 = nullptr;
-    pcnt_channel_handle_t pcnt_chan_2 = nullptr;
-
-    if ((pcnt_new_channel(encPcntUnit, &chan_1_config, &pcnt_chan_1) != ESP_OK) ||
-        (pcnt_new_channel(encPcntUnit, &chan_2_config, &pcnt_chan_2) != ESP_OK)) {
-        TT_LOG_E(TAG, "Pulsecounter channel config failed");
-    }
-
-    // Second argument is rising edge, third argument is falling edge
-    if ((pcnt_channel_set_edge_action(pcnt_chan_1, PCNT_CHANNEL_EDGE_ACTION_DECREASE, PCNT_CHANNEL_EDGE_ACTION_INCREASE) != ESP_OK) ||
-        (pcnt_channel_set_edge_action(pcnt_chan_2, PCNT_CHANNEL_EDGE_ACTION_INCREASE, PCNT_CHANNEL_EDGE_ACTION_DECREASE) != ESP_OK)) {
-        TT_LOG_E(TAG, "Pulsecounter edge action config failed");
-    }
-
-    // Second argument is low level, third argument is high level
-    if ((pcnt_channel_set_level_action(pcnt_chan_1, PCNT_CHANNEL_LEVEL_ACTION_KEEP, PCNT_CHANNEL_LEVEL_ACTION_INVERSE) != ESP_OK) ||
-        (pcnt_channel_set_level_action(pcnt_chan_2, PCNT_CHANNEL_LEVEL_ACTION_KEEP, PCNT_CHANNEL_LEVEL_ACTION_INVERSE) != ESP_OK)) {
-        TT_LOG_E(TAG, "Pulsecounter level action config failed");
-    }
-
-    if ((pcnt_unit_add_watch_point(encPcntUnit, LOW_LIMIT) != ESP_OK) ||
-        (pcnt_unit_add_watch_point(encPcntUnit, HIGH_LIMIT) != ESP_OK)) {
-        TT_LOG_E(TAG, "Pulsecounter watch point config failed");
-    }
-
-    if (pcnt_unit_enable(encPcntUnit) != ESP_OK) {
-        TT_LOG_E(TAG, "Pulsecounter could not be enabled");
-    }
-
-    if (pcnt_unit_clear_count(encPcntUnit) != ESP_OK) {
-        TT_LOG_E(TAG, "Pulsecounter could not be cleared");
-    }
-
-    if (pcnt_unit_start(encPcntUnit) != ESP_OK) {
-        TT_LOG_E(TAG, "Pulsecounter could not be started");
-    }
-}
-
-int TpagerEncoder::getEncoderPulses() const {
-    int pulses = 0;
-    pcnt_unit_get_count(encPcntUnit, &pulses);
-    return pulses;
-}
-
-
-bool TpagerEncoder::startLvgl(lv_display_t* display) {
-    initEncoder();
-
-    gpio_input_enable(ENCODER_ENTER);
-
-    encHandle = lv_indev_create();
-
-    lv_indev_set_type(encHandle, LV_INDEV_TYPE_ENCODER);
-    lv_indev_set_read_cb(encHandle, &readCallback);
-    lv_indev_set_display(encHandle, display);
-    lv_indev_set_user_data(encHandle, this);
-
-    return true;
-}
-
-bool TpagerEncoder::stopLvgl() {
-    lv_indev_delete(encHandle);
-    encHandle = nullptr;
-
-    return true;
-}

Boards/m5stack-cardputer-adv/Source/Configuration.cpp

@@ -1,145 +0,0 @@
-#include "devices/Display.h"
-#include "devices/SdCard.h"
-#include "devices/CardputerKeyboard.h"
-#include "devices/CardputerPower.h"
-
-#include <Tactility/hal/Configuration.h>
-#include <Tactility/lvgl/LvglSync.h>
-
-#include <PwmBacklight.h>
-#include <Tca8418.h>
-
-using namespace tt::hal;
-
-bool initBoot() {
-    return driver::pwmbacklight::init(LCD_PIN_BACKLIGHT, 512);
-}
-
-static DeviceVector createDevices() {
-    auto tca8418 = std::make_shared<Tca8418>(I2C_NUM_0);
-    return {
-        createSdCard(),
-        createDisplay(),
-        tca8418,
-        std::make_shared<CardputerKeyboard>(tca8418),
-        std::make_shared<CardputerPower>()
-    };
-}
-
-extern const Configuration hardwareConfiguration = {
-    .initBoot = initBoot,
-    .uiScale = UiScale::Smallest,
-    .createDevices = createDevices,
-    .i2c {
-        i2c::Configuration {
-            .name = "Main",
-            .port = I2C_NUM_0,
-            .initMode = i2c::InitMode::ByTactility,
-            .isMutable = false,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_8,
-                .scl_io_num = GPIO_NUM_9,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-        i2c::Configuration {
-            .name = "Port A", // Grove
-            .port = I2C_NUM_1,
-            .initMode = i2c::InitMode::Disabled,
-            .isMutable = true,
-            .config = (i2c_config_t) {
-                .mode = I2C_MODE_MASTER,
-                .sda_io_num = GPIO_NUM_2,
-                .scl_io_num = GPIO_NUM_1,
-                .sda_pullup_en = true,
-                .scl_pullup_en = true,
-                .master = {
-                    .clk_speed = 400000
-                },
-                .clk_flags = 0
-            }
-        },
-    },
-    .spi {
-        // Display
-        spi::Configuration {
-            .device = SPI2_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_35,
-                .miso_io_num = GPIO_NUM_NC,
-                .sclk_io_num = GPIO_NUM_36,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = LCD_SPI_TRANSFER_SIZE_LIMIT,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = tt::lvgl::getSyncLock()
-        },
-        // SDCard
-        spi::Configuration {
-            .device = SPI3_HOST,
-            .dma = SPI_DMA_CH_AUTO,
-            .config = {
-                .mosi_io_num = GPIO_NUM_14,
-                .miso_io_num = GPIO_NUM_39,
-                .sclk_io_num = GPIO_NUM_40,
-                .quadwp_io_num = GPIO_NUM_NC,
-                .quadhd_io_num = GPIO_NUM_NC,
-                .data4_io_num = GPIO_NUM_NC,
-                .data5_io_num = GPIO_NUM_NC,
-                .data6_io_num = GPIO_NUM_NC,
-                .data7_io_num = GPIO_NUM_NC,
-                .data_io_default_level = false,
-                .max_transfer_sz = 0,
-                .flags = 0,
-                .isr_cpu_id = ESP_INTR_CPU_AFFINITY_AUTO,
-                .intr_flags = 0
-            },
-            .initMode = spi::InitMode::ByTactility,
-            .isMutable = false,
-            .lock = nullptr
-        },
-
-    },
-    .uart {
-        uart::Configuration {
-            .name = "Port A",
-            .port = UART_NUM_1,
-            .rxPin = GPIO_NUM_2,
-            .txPin = GPIO_NUM_1,
-            .rtsPin = GPIO_NUM_NC,
-            .ctsPin = GPIO_NUM_NC,
-            .rxBufferSize = 1024,
-            .txBufferSize = 1024,
-            .config = {
-                .baud_rate = 115200,
-                .data_bits = UART_DATA_8_BITS,
-                .parity    = UART_PARITY_DISABLE,
-                .stop_bits = UART_STOP_BITS_1,
-                .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
-                .rx_flow_ctrl_thresh = 0,
-                .source_clk = UART_SCLK_DEFAULT,
-                .flags = {
-                    .allow_pd = 0,
-                    .backup_before_sleep = 0,
-                }
-            }
-        }
-    }
-};