Create DTS files for all devices and implement I2C changes (#466)

Devictree changes:
- Create DTS files for all remaining devices
- Update corresponding `devicetree.yaml`
- Remove `i2c` configuration from corresponding `tt::hal::Configuration`

Apps & HAL:
- Removed I2C Settings (we'll make a new one later after I rework that part of the HAL)
- Delete TactilityC GPIO and I2C functionality
- Delete Related SystemEvent types
- Refactor `tt::hal::i2c` to only use `struct Device*` wrapping

Scripting:
- Fix DevicetreeCompiler boolean parsing
- Create `build-all.py`

TactilityC/Include/tt_hal_gpio.h

@@ -1,82 +0,0 @@
-#pragma once
-
-#include <stdint.h>
-#include <stdbool.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/** Logical GPIO pin identifier used by the HAL. Typically maps to the SoC GPIO number. */
-typedef unsigned int GpioPin;
-/** Value indicating that no GPIO pin is used/applicable. */
-#define GPIO_NO_PIN -1
-
-/** GPIO pin mode used by the HAL.
- * @warning The order must match tt::hal::gpio::Mode
- */
-typedef enum {
-    /** Pin is disabled (high-impedance). */
-    GpioModeDisable = 0,
-    /** Pin configured as input only. */
-    GpioModeInput,
-    /** Pin configured as push-pull output only. */
-    GpioModeOutput,
-    /** Pin configured as open-drain output only. */
-    GpioModeOutputOpenDrain,
-    /** Pin configured for both input and output (push-pull). */
-    GpioModeInputOutput,
-    /** Pin configured for both input and output (open-drain). */
-    GpioModeInputOutputOpenDrain
-} GpioMode;
-
-/** Configure a single GPIO pin.
- * @param[in] pin      GPIO number to configure.
- * @param[in] mode     Desired I/O mode for the pin.
- * @param[in] pullUp   Enable internal pull-up if true.
- * @param[in] pullDown Enable internal pull-down if true.
- * @return true on success, false if the pin is invalid or configuration failed.
- */
-bool tt_hal_gpio_configure(GpioPin pin, GpioMode mode, bool pullUp, bool pullDown);
-
-/** Configure a set of GPIO pins in one call.
- * The bit index of pin N is (1ULL << N).
- * @param[in] pinBitMask Bit mask of pins to configure.
- * @param[in] mode       Desired I/O mode for the pins.
- * @param[in] pullUp     Enable internal pull-up on the selected pins if true.
- * @param[in] pullDown   Enable internal pull-down on the selected pins if true.
- * @return true on success, false if any pin is invalid or configuration failed.
- */
-bool tt_hal_gpio_configure_with_pin_bitmask(uint64_t pinBitMask, GpioMode mode, bool pullUp, bool pullDown);
-
-/** Set the input/output mode for the specified pin.
- * @param[in] pin  The pin to configure.
- * @param[in] mode The mode to set.
- * @return true on success, false if the pin is invalid or mode not supported.
- */
-bool tt_hal_gpio_set_mode(GpioPin pin, GpioMode mode);
-
-/** Read the current logic level of a pin.
- * The pin should be configured for input or input/output.
- * @param[in] pin The pin to read.
- * @return true if the level is high, false if low. If the pin is invalid, the
- *         behavior is implementation-defined and may return false.
- */
-bool tt_hal_gpio_get_level(GpioPin pin);
-
-/** Drive the output level of a pin.
- * The pin should be configured for output or input/output.
- * @param[in] pin   The pin to drive.
- * @param[in] level Output level to set (true = high, false = low).
- * @return true on success, false if the pin is invalid or not configured as output.
- */
-bool tt_hal_gpio_set_level(GpioPin pin, bool level);
-
-/** Get the number of GPIO pins available on this platform.
- * @return The count of valid GPIO pins.
- */
-int tt_hal_gpio_get_pin_count();
-
-#ifdef __cplusplus
-}
-#endif